Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly (Click here).



1. INSTALL NO. 2 CAMSHAFT BEARING
  1. Clean the No. 2 camshaft bearing.

  1. Install the camshaft bearing to the camshaft housing.



    A198177E04
  1. Using a vernier caliper, measure the distance between the camshaft housing edge and the camshaft bearing edge.

    Standard distance:
    1.15 to 1.85 mm (0.0453 to 0.0728 in.)

    Text in Illustration 
    *1
    Vernier Caliper



2. INSTALL NO. 1 CAMSHAFT BEARING


    A198176E03
  1. Clean the No. 1 camshaft bearing.
    Text in Illustration 
    *1
    Vernier Caliper

  1. Install the camshaft bearing to the No. 1 camshaft bearing cap.

  1. Using a vernier caliper, measure the distance between the camshaft bearing cap edge and the camshaft bearing edge.

    Standard dimension A - B or B - A:
    0 to 0.7 mm (0 to 0.0276 in.)



3. INSTALL OIL CONTROL VALVE FILTER


    A196915
  1. Install the oil control valve filter to the No. 1 camshaft bearing cap.



4. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    A196902E10
  1. Align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Knock Pin Hole
    *b
    Knock Pin



    A196904E33
  1. Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Exhaust Gear Assembly
    *a
    Incorrect
    *b
    Correct
    *c
    Clearance
    *d
    No Clearance
    *e
    Camshaft Flange



    A250991
  1. Fix the camshaft timing exhaust gear assembly with the bolt.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    Do not disassemble the camshaft timing exhaust gear assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (Click here).



5. SET TDC/COMPRESSION


    A252819E02
  1. Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.
    Text in Illustration 
    *a
    Timing Notch



6. INSTALL NO. 2 CAMSHAFT


  1. Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


    A361610E01


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap
    -
    -

  1. Clean the camshaft journals.

  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.



    A250992E02
  1. Hold up the chain sub-assembly and align the timing mark and the paint mark, and install the No. 2 camshaft.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Timing Mark

    HINT:
    Perform "Inspection After Repair" after replacing the No. 2 camshaft (Click here).



7. INSTALL CAMSHAFT


  1. Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


    A361610E01


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap
    -
    -

  1. Clean the camshaft journals.

  1. Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.



    A251007E02
  1. Install the camshaft to the camshaft housing sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Approximately 17°
    *b
    Knock Pin

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft (Click here).



8. INSTALL CAMSHAFT BEARING CAP


    A250994
  1. Confirm the marks and numbers on the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps and place them in their proper positions and directions.



    A250988E02
  1. Using several steps, uniformly tighten the 10 bolts in the sequence shown in the illustration.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



    A250989E02
  1. Using several steps, uniformly tighten the 11 bolts in the sequence shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Check the torque of each bolt again.



9. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


    A196903E05
  1. Check the camshaft timing gear assembly position.
    Text in Illustration 
    *a
    Advanced Position
    *b
    Retarded Position
    *c
    Knock Pin Hole
    *d
    Alignment Mark

    NOTICE:
    1. If the camshaft timing gear assembly is set to the advanced position, do not let the camshaft timing gear assembly rotate clockwise during installation.
    2. If the camshaft timing gear assembly has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear assembly to the most advanced position before tightening the camshaft timing gear assembly.



    A251004E01
  1. Install the camshaft timing gear assembly as shown in the illustration.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide



    A250998E01
  1. Turn the camshaft timing gear assembly approximately 180° counterclockwise.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide



    A250999E03
  1. Align the paint mark with the timing mark to install the chain sub-assembly.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Timing Mark

    HINT:
    "A" is not a timing mark.



    A196901E16
  1. Align and attach the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly.
    Text in Illustration 
    *a
    Knock Pin Hole
    *b
    Knock Pin



    A196904E33
  1. Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Gear Assembly
    *a
    Incorrect
    *b
    Correct
    *c
    Clearance
    *d
    No Clearance
    *e
    Camshaft Flange

  1. Secure the camshaft in place by hand, and then temporarily install the installation bolt to the camshaft timing gear assembly by hand.

    NOTICE:
    Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



  1. If the lock pin has not been released, release it.



      A249942E02
    1. After cleaning and degreasing the intake side VVT oil hole on the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
      Text in Illustration 
      *a
      Make a Hole
      *b
      Adhesive Tape Sealing Area

      NOTICE:
      Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.

    2. Make a hole in the adhesive tape covering the oil hole as shown in the illustration. (Procedure A)



    3. A251001
    4. Apply approximately 200 kPa (2.0 kgf/ cm2, 29 psi) of air pressure to the hole made in procedure A to release the lock pin.

      NOTICE:
      1. If air leaks out, reattach the adhesive tape.
      2. Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.

    5. Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

      HINT:
      Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.

    6. Remove the adhesive tape from the No. 1 camshaft bearing cap.



    A249935
  1. Using a wrench to hold the hexagonal portion of the camshaft, tighten the bolt.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.



    A287580E01
  1. Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Timing Mark

    HINT:
    1. "A" is not a timing mark.
    2. Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



10. ADD ENGINE OIL


    A198199
  1. Add 50 cc (3.1 cu. in.) of engine oil into the oil hole shown in the illustration.

    NOTICE:
    1. Oil must be added if the valve lash adjuster assemblies were removed.
    2. Make sure that the low pressure chamber and oil paths of the valve lash adjuster assemblies are full of engine oil.



11. INSTALL TIMING CHAIN GUIDE
  1. Install the timing chain guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



12. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    A245327E01
  1. Turn the crankshaft pulley approximately 10° clockwise.



    A249933
  1. Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure not to drop the gasket inside the timing chain cover sub-assembly.

  1. Remove the pin from the stopper plate.



13. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION


  1. Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.


    A287581E01


    Text in Illustration 
    *a
    Timing Mark
    *b
    Timing Notch
    *c
    Approximately 7°
    *d
    Approximately 32°

  1. Check that both timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

    HINT:
    "A" is not a timing mark.



14. INSTALL TIMING CHAIN COVER PLATE


    A250986
  1. Install a new gasket and the timing chain cover plate with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



15. INSTALL TIMING CHAIN COVER TIGHT PLUG


    A196859
  1. Using a 14 mm hexagon wrench, install a new gasket and the plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



16. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A196857
  1. Apply a light coat of engine oil to 3 new gaskets.

  1. Install the 3 gaskets to the camshaft bearing caps.

  1. Install a new gasket to the cylinder head cover.

    NOTICE:
    Remove any oil from the contact surface.



    A196891E03
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 6.0 mm (0.118 to 0.236 in.)

    Application width A:
    5.0 mm (0.197 in.)

    Text in Illustration 
    *1
    Seal Packing
    *2
    Timing Chain Cover
    *3
    Camshaft Housing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A195876E01
  1. Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover.

  1. Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. Do not apply oil for at least 4 hours after the installation.



17. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 4 ignition coil assemblies with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).

  1. Connect the 4 ignition coil assembly connectors.



18. CONNECT ENGINE WIRE


    A250626E01
  1. Connect the engine wire to the engine assembly with the bolts and nuts.

    Torque:
    Nut (A):
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
    Nut (B):
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connectors and clamps.



19. INSTALL NO. 2 ENGINE ROOM RELAY BLOCK (w/ No. 2 Engine Room Relay Block)
  1. Engage the 2 clamps and install the No. 2 engine room relay block with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the front fender liner RH with the screw.



20. INSTALL ENGINE MOVING CONTROL ROD BRACKET


    A255916E01
  1. When the engine moving control rod has been replaced.

    1. Temporarily install the engine moving control rod bracket with the 4 bolts.

    2. Fully tighten the engine moving control rod bracket with the bolts except bolt A.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }



    3. A265927E01
    4. Fully tighten the bolt A.

      SST
      09961-00950  

      Torque:
      Without SST:
      52 N*m{ 530 kgf*cm , 38 ft.*lbf }
      With SST:
      33 N*m{ 340 kgf*cm , 25 ft.*lbf }

      NOTICE:
      1. The "with SST" torque value is effective when using SST with a fulcrum length of 150 mm (5.91 in.) and a torque wrench with a fulcrum length of 260 mm (10.24 in.) (Click here).
      2. The "with SST" torque value is effective when SST is parallel to the torque wrench.
      3. Fully tighten bolt A using SST.



    A255452E01
  1. When the engine moving control rod has been reused.

    1. Temporarily install the engine moving control rod bracket with the 4 bolts.

    2. Fully tighten the engine moving control rod bracket with the 4 bolts.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }



21. INSTALL EARTH WIRE
  1. Install the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



22. INSTALL NO. 2 ENGINE MOUNTING STAY RH
  1. Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



23. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A255405E01
  1. Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
    Text in Illustration 
    *a
    Wire harness clamp
    *b
    Hole
    *c
    Projection

  1. Tighten the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the wire harness clamp.



24. INSTALL AIR CLEANER FILTER ELEMENT


25. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Install the air cleaner hose with the hose clamp.

  1. Connect the ventilation hose to the cylinder head cover.

  1. Install the fuel vapor feed hose to the air cleaner hose.

  1. Connect the mass air flow meter connector and 2 wire harness clamps to the air cleaner cap sub-assembly.

  1. Connect the vacuum switching valve assembly to the air cleaner hose.



26. INSTALL INLET AIR CLEANER ASSEMBLY
  1. Install the inlet air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



28. INSPECT FOR OIL LEAK


29. INSTALL FRONT FENDER APRON SEAL RH


30. INSTALL ENGINE UNDER COVER RH


31. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


32. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Fit the 3 retainers and install the No. 1 engine cover sub-assembly.



33. INSTALL COOL AIR INTAKE DUCT SEAL (for TMC, TMMR Made)
  1. Install the cool air intake duct seal with the 9 clips.



34. INSTALL COOL AIR INTAKE DUCT SEAL (for TMMK Made)
  1. Install the cool air intake duct seal with the 9 clips.



35. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }