Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › CYLINDER HEAD GASKET

CYLINDER HEAD GASKET > REMOVAL

for Preparation Click here



1. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
(Click here)


2. REMOVE MANIFOLD STAY


    A195975
  1. Remove the bolt, nut and manifold stay.



3. REMOVE NO. 2 MANIFOLD STAY


    A209598
  1. Remove the bolt, nut and No. 2 manifold stay.



4. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A209579
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator.



5. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly.



    A195981E01
  1. Remove the exhaust manifold to head gasket.



6. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY


    A254781
  1. Disconnect the fuel tube from the clamp.

  1. Disconnect the throttle body connector.



    A254780
  1. Disconnect the water by-pass hose from the throttle with motor body assembly.

  1. Disconnect the No. 2 water by-pass hose from the throttle with motor body assembly.



    A195069
  1. Remove the 4 bolts and the throttle body with fuel tube bracket.



    A195070
  1. Remove the bolt and fuel tube bracket.



    A195071
  1. Remove the gasket from the intake manifold.



7. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A254719
  1. Disconnect the union to connector tube hose and wire harness clamp.

  1. Disconnect the 2 vacuum hoses and connector.

  1. Remove the bolt and vacuum switching valve assembly.



    A254721
  1. Remove the bolt and vacuum hose clamp.



8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A252631
  1. Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 fuel injector assemblies.

    NOTICE:
    Do not drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



    A211217E01
  1. Remove the 2 fuel delivery spacers from the cylinder head.
    Text in Illustration 
    *1
    Fuel Delivery Spacer
    *2
    Injector Vibration Insulator

  1. Remove the 4 injector vibration insulators from the cylinder head.



9. DISCONNECT NO. 2 VENTILATION HOSE


    A196046
  1. Disconnect the No. 2 ventilation hose from the intake manifold.



10. REMOVE INTAKE MANIFOLD


    A205609
  1. Remove the 2 bolts and 2 wire harness clamp brackets.



    A254751
  1. Disconnect the fuel vapor feed hose.

  1. Disconnect the 3 wire harness clamps and connector.

  1. Remove the bolt and wire harness clamp bracket.



    A199910
  1. Apply battery voltage to the terminals of the connector to close the tumble control valves (w/ TCV).

    Standard:
    Tester Connection
    Specified Condition
    Positive (+) battery voltage applied to terminal 8 (M-), and negative (-) battery voltage applied to terminal 4 (M+)
    Open → Closed

    NOTICE:
    1. If this procedure is not performed, the tumble control valves may be damaged when the intake manifold is removed.
    2. Apply battery voltage for 1 to 3 seconds.
    3. If battery voltage is applied for more than 3 seconds, the actuator may be damaged.
    4. Do not allow the lead wires to contact the other terminals.



    A256257E01
  1. Remove the bolt and separate the wire harness.

  1. Disconnect the 2 wire harness clamps and intake air control valve actuator connector (w/ TCV).

  1. Disconnect the 2 wire harness clamps (w/o TCV).
    Text in Illustration 
    *A
    w/ TCV
    *B
    w/o TCV



    A254722
  1. Remove the 6 bolts and intake manifold (w/ TCV).

    NOTICE:
    The tumble control valves may be damaged if they are not closed before removing the intake manifold.

    HINT:
    Connect the battery to the terminals of the actuator to operate the motor and close the valves .



    A254723
  1. Remove the 6 bolts and intake manifold (w/o TCV).



    A207714
  1. Remove the intake manifold gasket from the intake manifold (w/ TCV).



    A254724
  1. Remove the intake manifold gasket from the intake manifold (w/o TCV).



    A196049
  1. Disconnect the 2 vacuum hoses from the intake manifold and remove the No. 1 check valve.



    A196050
  1. Remove the bolt and wire harness clamp bracket.



11. SET NO. 1 CYLINDER TO TDC/COMPRESSION


  1. Temporarily install the crankshaft pulley bolt.


    A200698E03


    Text in Illustration 
    *a
    Approximately 7°
    *b
    Approximately 32°
    *c
    Timing Mark
    *d
    Key

    HINT:
    "A" is not a timing mark.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.

  1. Remove the crankshaft pulley bolt.



12. REMOVE TIMING CHAIN GUIDE


    A196878
  1. Remove the bolt and timing chain guide.



13. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A196879E02
  1. Allow the plunger to extend slightly, and then rotate the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the tensioner.
    Text in Illustration 
    *1
    Stopper Plate
    *2
    Plunger



    A196880E02
  1. Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
    Text in Illustration 
    *1
    Pin



    A196877
  1. Remove the 2 bolts, chain tensioner and gasket.



14. REMOVE CHAIN TENSIONER SLIPPER


    A196876
  1. Remove the bolt and chain tensioner slipper.



15. REMOVE CHAIN SUB-ASSEMBLY
  1. Remove the chain sub-assembly.



16. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A196868
  1. Remove the 2 bolts and chain vibration damper.



17. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    A196882
  1. Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing gear.

    NOTICE:
    1. Be careful not to damage the cylinder head or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing gear.



18. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    A198183
  1. Hold the hexagonal portion of the camshaft with a wrench and remove the bolt and camshaft timing exhaust gear.

    NOTICE:
    1. Be careful not to damage the cylinder head or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing exhaust gear.



19. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY


    A196884E01
  1. Uniformly loosen and remove the 20 bearing cap bolts in the sequence shown in the illustration.



    A196899
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.



20. REMOVE CAMSHAFT BEARING CAP


    A196885E01
  1. Remove the 11 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.



21. REMOVE OIL CONTROL VALVE FILTER


    A196915
  1. Remove the oil control valve filter from the No. 1 camshaft bearing cap.



22. REMOVE NO. 1 CAMSHAFT BEARING


    A196916
  1. Remove the No. 1 camshaft bearing.



23. REMOVE CAMSHAFT
  1. Remove the camshaft and No. 2 camshaft.



24. REMOVE NO. 2 CAMSHAFT BEARING


    A196917
  1. Remove the No. 2 camshaft bearing.



25. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 16 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



26. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 16 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



27. REMOVE VALVE STEM CAP
  1. Remove the 16 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



28. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A196908E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to keep the removed parts separate for each installation position.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Remove the cylinder head.



29. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head gasket from the cylinder block.