Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2650    Slide Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH (w/ Memory) does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2650
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch LH (w/ Memory)
  2. Slide motor (Separate type front seat cushion assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B342629E13


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SLIDE MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Driver Seat / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Driver Seat (Front Power Seat Switch LH (w/ Memory)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Slide Operation
    Seat slide operation
    OFF/Rear/Front
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (SLIDE MOTOR CIRCUIT)
  1. Disconnect the e8 slide motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e8-2 - e8-3
    Slide switch on
    4.8 to 5.1 V



NG
Go to step 4
OK


3.CHECK SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY)


    B325956E42
  1. Reconnect the e8 slide motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e8-2 - Body ground
    Slide switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Slide Motor (Separate Type Front Seat Cushion Assembly))



NG
REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - SLIDE MOTOR)
  1. Disconnect the e12 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-5 (SSRS) - e8-2
    Always
    Below 1 Ω
    e12-1 (SGND) - e8-3
    Always
    Below 1 Ω
    e12-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

5.INSPECT SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY)


    B238256E14
  1. Disconnect the e8 slide motor connector.

  1. Check if the seat cushion moves smoothly when the battery is connected to the slide motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Seat cushion moves forward
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Seat cushion moves backward

    Text in Illustration 
    *a
    Component without harness connected
    (Slide Motor (Separate Type Front Seat Cushion Assembly))



NG
REPLACE SLIDE MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - SLIDE MOTOR)
  1. Disconnect the e11 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e11-3 (SLD+) - e8-4
    Always
    Below 1 Ω
    e11-4 (SLD-) - e8-1
    Always
    Below 1 Ω
    e11-3 (SLD+) - Body ground
    Always
    10 kΩ or higher
    e11-4 (SLD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)