Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2651    Reclining Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH (w/ Memory) does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2651
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch LH (w/ Memory)
  2. Reclining motor (Separate type front seatback assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B342629E14


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (RECLINING MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Driver Seat / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Driver Seat (Front Power Seat Switch LH (w/ Memory)) 
    Tester Display
    Test Part
    Control Ranger
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    OFF/Rear/Front
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (RECLINING MOTOR CIRCUIT)
  1. Disconnect the g3 reclining motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    g3-2 - g3-3
    Reclining switch on
    4.8 to 5.1 V



NG
Go to step 4
OK


3.CHECK RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK ASSEMBLY)


    B325956E43
  1. Reconnect the g3 reclining motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    g3-2 - Body ground
    Reclining switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Reclining Motor (Separate Type Front Seatback Assembly))



NG
REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK ASSEMBLY) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - RECLINING MOTOR)
  1. Disconnect the e12 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-11 (SSRR) - g3-2
    Always
    Below 1 Ω
    e12-1 (SGND) - g3-3
    Always
    Below 1 Ω
    e12-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

5.INSPECT RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK ASSEMBLY)


    B238256E14
  1. Disconnect the g3 reclining motor connector.

  1. Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Seatback moves forward
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Seatback moves backward

    Text in Illustration 
    *a
    Component without harness connected
    (Reclining Motor (Separate Type Front Seatback Assembly))



NG
REPLACE RECLINING MOTOR (SEPARATE TYPE FRONT SEATBACK ASSEMBLY) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - RECLINING MOTOR)
  1. Disconnect the e11 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e11-9 (RCL+) - g3-4
    Always
    Below 1 Ω
    e11-11 (RCL-) - g3-1
    Always
    Below 1 Ω
    e11-9 (RCL+) - Body ground
    Always
    10 kΩ or higher
    e11-11 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)