Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2652    Front Vertical Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH (w/ Memory) does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2652
The upward and downward lock detection position of the sensor the same.
  1. Front power seat switch LH (w/ Memory)
  2. Front vertical motor (Separate type front seat cushion assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B342629E15


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FRONT VERTICAL MOTOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Driver Seat / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Driver Seat (Front Power Seat Switch LH (w/ Memory)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Vertical Operation
    Seat front vertical operation
    OFF/Down/Up
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (FRONT VERTICAL MOTOR CIRCUIT)
  1. Disconnect the e9 front vertical motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e9-2 - e9-3
    Front vertical switch on
    4.8 to 5.1 V



NG
Go to step 4
OK


3.CHECK FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY)


    B325956E44
  1. Reconnect the e9 front vertical motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e9-2 - Body ground
    Front vertical switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Front Vertical Motor (Separate Type Front Seat Cushion Assembly))



NG
REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY - FRONT VERTICAL MOTOR)
  1. Disconnect the e12 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-3 (SSFV) - e9-2
    Always
    Below 1 Ω
    e12-1 (SGND) - e9-3
    Always
    Below 1 Ω
    e12-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)  

5.INSPECT FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY)


    B238256E14
  1. Disconnect the e9 front vertical motor connector.

  1. Check if the seat cushion moves smoothly when the battery is connected to the front vertical motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Seat cushion moves upward
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Seat cushion moves downward

    Text in Illustration 
    *a
    Component without harness connected
    (Front Vertical Motor (Separate Type Front Seat Cushion Assembly))



NG
REPLACE FRONT VERTICAL MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY - FRONT VERTICAL MOTOR)
  1. Disconnect the e11 front power seat switch LH (w/ Memory) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e11-8 (FRV+) - e9-4
    Always
    Below 1 Ω
    e11-5 (FRV-) - e9-1
    Always
    Below 1 Ω
    e11-8 (FRV+) - Body ground
    Always
    10 kΩ or higher
    e11-5 (FRV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)