DTC B2653 Lifter Sensor Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B2653 | The upward and downward lock detection position of the sensor is the same. |
|

| 1.PERFORM ACTIVE TEST USING GTS (LIFTER MOTOR) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
|
| ||||
| OK | |
| 2.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (LIFTER MOTOR CIRCUIT) |
Disconnect the e10 lifter motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e10-2 - e10-3 | Lifter switch on | 4.8 to 5.1 V |
|
| ||||
| OK | |
| 3.CHECK LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) |
![]() |
Reconnect the e10 lifter motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| e10-2 - Body ground | Lifter switch on | 4.5 to 4.8 V |
| *a | Component with harness connected (Lifter Motor (Separate Type Front Seat Cushion Assembly)) |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - LIFTER MOTOR) |
Disconnect the e12 front power seat switch LH (w/ Memory) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| e12-4 (SSRL) - e10-2 | Always | Below 1 Ω |
| e12-1 (SGND) - e10-3 | Always | Below 1 Ω |
| e12-4 (SSRL) - Body ground | Always | 10 kΩ or higher |
| e12-1 (SGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.INSPECT LIFTER MOTOR (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY) |
![]() |
Disconnect the e10 lifter motor connector.
Check if the seat cushion moves smoothly when the battery is connected to the lifter motor connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Seat cushion moves upward |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Seat cushion moves downward |
| *a | Component without harness connected (Lifter Motor (Separate Type Front Seat Cushion Assembly)) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - LIFTER MOTOR) |
Disconnect the e11 front power seat switch LH (w/ Memory) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| e11-10 (LFT+) - e10-4 | Always | Below 1 Ω |
| e11-12 (LFT-) - e10-1 | Always | Below 1 Ω |
| e11-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| e11-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||