Home › Engine / Hybrid System ยท CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise SET Indicator Light Circuit

for Preparation Click here


DESCRIPTION

  1. The ECM turns on the SET indicator by sending indicator output demand signals to the combination meter assembly using CAN communication.
  2. The cruise control SET indicator illuminates when the cruise control system is controlling vehicle speed.
  3. The cruise control indicator circuit uses CAN communication. If the cruise control indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.

WIRING DIAGRAM

Refer to Cruise Main Indicator Light Circuit (Click here).

INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (METER DISPLAY 1)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Combination Meter 
    Tester Display
    Measurement Item
    Control Range
    Diagnostic Note
    Meter Display 1
    Multi-information display
    OFF or All
    -

    Result:
    Result
    Proceed to
    The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. (for 2AR-FE, 2GR-FE)
    A
    The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. (for 6AR-FSE)
    B
    The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test.
    C



B
Go to step 3

C
GO TO METER / GAUGE SYSTEM (Click here)
A


2.READ VALUE USING GTS (SET/COAST SWITCH)
  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -

    Result:
    Result
    Proceed to
    The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-/SET switch).
    A
    The cruise control SET indicator does not illuminate but the Data List item SET/ COAST Switch changes according to the operation of the cruise control main switch (-/SET switch).
    B
    The cruise control SET indicator does not illuminate and the Data List item SET/ COAST Switch does not change according to the operation of the cruise control main switch (-/SET switch) (for 2AR-FE).
    C
    The cruise control SET indicator does not illuminate and the Data List item SET/ COAST Switch does not change according to the operation of the cruise control main switch (-/SET switch) (for 2GR-FE).
    D



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.READ VALUE USING GTS (-SET SWITCH)
  1. Enter the following menus: Powertrain / Cruise Control / Data List.

  1. Read the Data List according to the display on the GTS.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    -SET Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -

    Result:
    Result
    Proceed to
    The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-/SET switch).
    A
    The cruise control SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the cruise control main switch (-/SET switch).
    B
    The cruise control SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the cruise control main switch (-/SET switch).
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE ECM (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)