Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD (for TMMK Made)

INSTRUMENT PANEL SAFETY PAD (for TMMK Made) > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR SCUFF PLATE LH


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B399740
  1. Disconnect the front door opening trim weatherstrip LH.



6. REMOVE INSTRUMENT SIDE PANEL LH


    B377599
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B399733
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B399734
  1. Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.



8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B377605
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B377606
  1. Disengage the 2 clips as shown in the illustration.



    B377608
  1. Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.



9. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.



    B399735
  1. Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.



    B377610
  1. Disengage the 5 claws, 5 clips and 2 guides.

  1. Disconnect each connector.



    B377611
  1. Remove the instrument cluster finish panel assembly as shown in the illustration.



10. REMOVE COMBINATION METER ASSEMBLY


    E226414
  1. Remove the 4 screws.



    E306607
  1. Disengage the wire harness clamp.

  1. Disconnect the 2 connectors to remove the combination meter assembly.



11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



12. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B403736
  1. Remove the bolt <B> and screw <C> or <D>.



    B377614
  1. Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.



13. REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY


    B377618
  1. Disengage the 4 clips and remove the upper console box sub-assembly.

  1. w/ Seat Heater System:

    1. Disconnect each connector.



14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B377615
  1. Disengage the 2 claws as shown in the illustration.



    B377616
  1. Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.



15. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
  1. Move the shift lever to N.



    B403737
  1. Disconnect the connector.

  1. Remove the 2 screws <C> or <D>.



    B377620
  1. Disengage the 6 clips and remove the rear console upper panel sub-assembly.



16. REMOVE CONSOLE BOX CUP HOLDER


    B380961
  1. Remove the console box cup holder from the rear console upper panel sub-assembly.



17. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY


    B380962
  1. Remove the 6 screws <E> and instrument panel cup holder tray.

  1. Remove the front console upper panel garnish.



18. REMOVE NO. 4 CONSOLE BOX DUCT


    B293623
  1. Disengage the claw and remove the No. 4 console box duct.



19. REMOVE CONSOLE BOX CARPET


    B377626
  1. Remove the console box carpet.



20. REMOVE REAR CONSOLE BOX ASSEMBLY


    B380929
  1. Disconnect the connector and disengage the clamp.



    B405578
  1. Remove the 2 bolts and 2 screws.



    B380931
  1. Pull the rear console box assembly in the direction indicated by the arrow to disengage the 4 guides and remove the rear console box assembly.



21. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    B377624
  1. Using a moulding remover, disengage the 11 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 1 speaker opening cover assembly.



22. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B403738
  1. Remove the 2 screws <C> or <D>.



    B377622
  1. Disengage the 2 clips and guide as shown in the illustration.

  1. Disconnect each connector to remove the upper console panel sub-assembly.



23. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


    E300869E01
  1. Apply protective tape to the areas shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    E300871
  1. Remove the 4 bolts and 2 screws.



    E300873
  1. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle to disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.



24. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)


    E300870E01
  1. Apply protective tape to the areas shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    E300872
  1. Remove the 4 bolts and 2 screws.



    E300874
  1. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle to disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.



25. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)

NOTICE:
Do not touch the speaker cone.



    E300881
  1. Remove the 2 screws.

  1. Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.



26. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



27. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



28. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B380933
  1. Disconnect the front door opening trim weatherstrip RH.



29. REMOVE INSTRUMENT SIDE PANEL RH


    B380934
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B380936
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



30. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B279888
  1. Disengage the 4 claws.

  1. Disengage the 2 guides.

  1. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.



31. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B279740
  1. Remove the 3 bolts.



    B279759
  1. Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

    NOTICE:
    When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.



    B279741E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



32. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B380937
  1. Remove the 2 screws <C> or <D>.

  1. Open the lower instrument panel door.



    B403739
  1. Remove the 3 screws <C> or <D>.



    B380939
  1. Disengage the 2 clips and guide as shown in the illustration.



    B380941
  1. Disengage the clamp.

  1. Disengage the glove compartment light as shown in the illustration.

  1. Disconnect the connector and remove the lower instrument panel sub-assembly.



33. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B380943
  1. Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.



34. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    B380945
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B380946
  1. Disengage the 2 clips as shown in the illustration.



    B380947
  1. Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.



35. REMOVE FRONT PILLAR GARNISH LH


    B379543E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang from the front pillar garnish clip.



    B379544E02
  1. While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrows (A) shown in the illustration, disengage the front pillar garnish clip.

    NOTICE:
    Do not apply excessive force using a tool.

  1. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

  1. Remove the 2 clips from the front pillar garnish LH.



    B278988E02
  1. Protect the curtain shield airbag assembly LH.
    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly LH
    *a
    Protective Cover
    V100155
    Adhesive Tape

    1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.



36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B280301
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B280302
  1. Using a moulding remover, disengage the 2 clips and 3 claws.

  1. Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.



37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

NOTICE:
Do not touch the speaker cone.



    E300880
  1. Remove the 2 screws.

  1. Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.



38. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side .



39. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B279896
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B279897
  1. Using a moulding remover, disengage the 2 clips and 3 claws.

  1. Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.



40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure as for the LH side .



41. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    B293657
  1. Disengage the 4 clips and guide.

  1. Disconnect the connector to remove the lower instrument panel finish panel assembly.



42. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    B380949
  1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



    B403740
  1. Remove the screw <C> or <D>.



    B380951
  1. Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.



43. REMOVE CONSOLE BOX INSERT


    B403741
  1. Remove the screw <C> or <D>.



    B380954
  1. Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.



44. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


  1. Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


    B280294



45. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B278792E01
  1. Slide the slider to release the lock, and then disconnect the connector.
    Text in Illustration 
    *a
    Slider

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



46. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    B380956
  1. Remove the 2 bolts <B>.

  1. Disengage the clamp to remove the radio tuner mounting bracket.



  1. Disconnect each connector.


    B380957

  1. Disengage each clamp.



  1. Remove the 2 passenger airbag bolts <A>.


    B380958E01


    Text in Illustration 
    *a
    Passenger Airbag Bolt <A>
    *b
    Bolt <B>
    *c
    Nut <F> or <G>
    *d
    Clip

  1. Remove the 3 bolts <B> and nut <F> or <G>.

  1. Remove the 2 clips.



  1. Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.


    B380959

    NOTICE:
    1. Do not damage the instrument panel safety pad assembly.
    2. Do not allow the wire harnesses to interfere with the surrounding parts.