Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY (for TMC, TMMR Made)

CENTER AIRBAG SENSOR ASSEMBLY (for TMC, TMMR Made) > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE CONSOLE BOX ASSEMBLY
(Click here)


4. REMOVE FRONT DOOR SCUFF PLATE LH


    B278977
  1. Disengage the 10 claws and remove the front door scuff plate LH.



5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.



7. REMOVE INSTRUMENT SIDE PANEL LH


    B280320
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B280322
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



8. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



9. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY


    B386769
  1. Remove the 2 bolts <B>.



  1. w/o Driver Side Knee Airbag:



      B386777
    1. Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.



  1. w/ Driver Side Knee Airbag:



      B386770
    1. Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.



10. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B386778
    1. Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:



      B386772
    1. Disengage the 2 claws as shown in the illustration.

    2. Disconnect each connector to remove the front console upper panel garnish.



11. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


    B384412
  1. Remove the 2 screws <D>.



    B384413
  1. Disengage the 2 clips as shown in the illustration.

  1. Disconnect each connector to remove the front ash receptacle assembly.



12. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side .



13. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side .



14. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the instrument side panel RH.



15. REMOVE INSTRUMENT SIDE PANEL RH


    B281763
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B281765
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



16. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B279888
  1. Disengage the 4 claws.

  1. Disengage the 2 guides.

  1. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.



17. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B281767
  1. Remove the bolt <B> and screw <D>.

  1. Open the lower instrument panel door.



    B281768
  1. Remove the 3 screws <D>.



    B281769
  1. Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.



18. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


  1. for LHD:



      B280290
    1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



    B281774
  1. Remove the 2 screws <D>.



    B281775
  1. Disengage the clip and 4 guides to remove the front No. 2 console box insert as shown in the illustration.



19. REMOVE CONSOLE BOX INSERT


  1. for RHD:



      B281942
    1. Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.



    B281777
  1. Remove the 2 screws <D>.



    B281778
  1. Disengage the clip and 4 guides to remove the console box insert as shown in the illustration.



20. REMOVE FLOOR CARPET BRACKET LH


    E227160
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket LH.



21. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



22. REMOVE NO. 1 CONSOLE BOX DUCT


    E227163
  1. Remove the clip and No. 1 console box duct.



23. REMOVE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Turn back the carpet.



    B278814
  1. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and airbag sensor assembly.