Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › CLEARANCE WARNING ECU

CLEARANCE WARNING ECU > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side .



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side .



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B284920
  1. Disconnect the front door opening trim weatherstrip RH.



6. REMOVE INSTRUMENT SIDE PANEL RH


    B281763
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B281765
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



7. REMOVE FRONT PANEL GARNISH RH


    B386771
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish RH.



8. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    B279888
  1. Disengage the 4 claws.

  1. Disengage the 2 guides.

  1. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.



9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


    B281767
  1. Remove the bolt <B> and screw <C>.

  1. Open the lower instrument panel door.



    B281768
  1. Remove the 3 screws <C>.



    B281769
  1. Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.



10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    B281782
  1. Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

  1. w/ Smart Entry and Start System:

    1. Disconnect the connector.



11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)


    B386769
  1. Remove the 2 bolts <B>.



  1. w/o Driver Side Knee Airbag:



      B386777
    1. Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.



  1. w/ Driver Side Knee Airbag:



      B386770
    1. Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.



13. REMOVE ECU INTEGRATION BOX RH


  1. for LHD:

    1. Disconnect each connector.



    2. E223728
    3. Remove the bolt, 2 nuts and ECU integration box RH.



  1. for RHD:

    1. Disconnect each connector.



    2. E227952
    3. Remove the bolt, 2 nuts and ECU integration box RH.



14. REMOVE CLEARANCE WARNING ECU ASSEMBLY


  1. for LHD:



      E223729
    1. Disengage the 2 claws and remove the clearance warning ECU assembly.



  1. for RHD:



      E229573
    1. Disengage the 2 claws and remove the clearance warning ECU assembly.