Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for TMMK Made)

REAR SEAT OUTER BELT ASSEMBLY (for TMMK Made) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR SEAT CUSHION ASSEMBLY


    B279202E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



4. REMOVE REAR SEAT CUSHION LOCK HOOK


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



5. REMOVE INNER LUGGAGE COMPARTMENT TRIM PAD


    B279201
  1. Remove the inner luggage compartment trim pad.



6. REMOVE REAR SEATBACK ASSEMBLY LH


    B279209E02
  1. Disengage the 2 fasteners as shown in the illustration.
    Text in Illustration 
    *a
    Fastener



    B279211
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285010
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly LH.



8. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285009
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly RH.



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip LH.



10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Disconnect the rear door opening trim weatherstrip RH.



11. REMOVE ROOF SIDE INNER GARNISH LH


    B387550
  1. Disengage the 5 clips.

  1. Disengage the guide and remove the roof side inner garnish LH.

  1. Remove the 5 clips from the roof side inner garnish LH.



12. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B271094
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



14. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B271092
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



15. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    B279428
  1. Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.



16. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


  1. for Type A:



      B271090
    1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



  1. for Type B:



      B414445
    1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



17. REMOVE CENTER STOP LIGHT SET


    E226678E01
  1. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.



    E231297
  1. Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

    HINT:
    This makes it easier to disconnect the connector.

  1. Disconnect the connector and remove the center stop light set.



18. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    B271100
  1. Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.

    HINT:
    Use the same procedure for the other 2 child restraint seat tether anchor covers.



19. REMOVE REAR SEAT SHOULDER BELT COVER


    B271099
  1. Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    B279423E02
  1. Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the tip of the pliers before use.

  1. Disengage the 5 guides.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.



21. REMOVE REAR SEAT OUTER BELT ASSEMBLY


    B271097
  1. Remove the bolt.

  1. Disengage the guide to remove the rear seat outer belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.