Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The sound signals amplified by the radio receiver assembly are sent to the speakers from the radio receiver assembly via the speaker circuits.
If there is a short in a speaker circuit, the radio receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly, telematics transceiver or speakers.
If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


E360471E04


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System (Click here).

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - SPEAKERS)
  1. Disconnect the I148 and I149 radio receiver assembly connectors.

  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I1 and I83 front No. 2 speaker assembly connectors.

  1. Disconnect the O21 and O18 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I148-1 (FR+) - I218-2 (SPI+)
    Always
    Below 1 Ω
    I148-5 (FR-) - I218-3 (SPI-)
    Always
    Below 1 Ω
    I218-5 (SPO+) - I83-4 (TWR+)
    Always
    Below 1 Ω
    I218-6 (SPO-) - I83-2 (TWR-)
    Always
    Below 1 Ω
    I83-3 (+) - J5-1
    Always
    Below 1 Ω
    I83-1 (-) - J5-2
    Always
    Below 1 Ω
    I148-2 (FL+) - I1-4 (TWL+)
    Always
    Below 1 Ω
    I148-6 (FL-) - I1-2 (TWL-)
    Always
    Below 1 Ω
    I1-3 (+) - K5-1
    Always
    Below 1 Ω
    I1-1 (-) - K5-2
    Always
    Below 1 Ω
    I149-1 (RR+) - O18-1
    Always
    Below 1 Ω
    I149-3 (RR-) - O18-2
    Always
    Below 1 Ω
    I149-2 (RL+) - O21-1
    Always
    Below 1 Ω
    I149-6 (RL-) - O21-2
    Always
    Below 1 Ω
    I148-1 (FR+) or I218-2 (SPI+) - Body ground
    Always
    10 kΩ or higher
    I148-5 (FR-) or I218-3 (SPI-) - Body ground
    Always
    10 kΩ or higher
    I218-5 (SPO+) or I83-4 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I218-6 (SPO-) or I83-2 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I83-3 (+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I148-2 (FL+) or I1-4 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I148-6 (FL-) or I1-2 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) or K5-2 - Body ground
    Always
    10 kΩ or higher
    I149-1 (RR+) or O18-1 - Body ground
    Always
    10 kΩ or higher
    I149-3 (RR-) or O18-2 - Body ground
    Always
    10 kΩ or higher
    I149-2 (RL+) or O21-1 - Body ground
    Always
    10 kΩ or higher
    I149-6 (RL-) or O21-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT TELEMATICS TRANSCEIVER
  1. Remove the telematics transceiver (Click here).



    E169849E41
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SPI+) - 5 (SPO+)
    Always
    Below 1 Ω
    3 (SPI-) - 6 (SPO-)
    Always
    Below 1 Ω
    2 (SPI+) - 3 (SPI-)
    Always
    10 kΩ or higher
    5 (SPO+) - 6 (SPO-)
    Always
    10 kΩ or higher
    2 (SPI+) or 5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    3 (SPI-) or 6 (SPO-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Telematics Transceiver)



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

5.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)