Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for TMMK Made)

FRONT DOOR LOCK (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B380633
  1. Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug as shown in the illustration.



4. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER


    B380639
  1. Disengage the 2 claws and 2 guides to remove the front door front lower frame upper cover.



5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B380635
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator master switch assembly with front door armrest base panel.



6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B401212
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator switch assembly with front door armrest base panel.



7. REMOVE FRONT ARMREST ASSEMBLY


    B277187
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the front armrest assembly.



8. REMOVE COURTESY LIGHT ASSEMBLY


    E226714E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *1
    Protective Tape

  1. Disconnect the connector and remove the courtesy light assembly.



9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B380640E01
  1. Apply protective tape to the front door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380641
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 10 clips.



    B380642E01
  1. Pull out the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Front Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the front door panel.

  1. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.



    B380644
  1. Disengage the clamp.

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.



10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B380647E01
  1. Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



11. REMOVE DOOR SIDE AIRBAG SENSOR
  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Disconnect the connector from the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


      H043302E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connector Lock is Released
      -
      -

    2. Push down the white housing lock again and disconnect the connector.

      NOTICE:
      Do not push down the part (A) shown in the illustration when disconnecting.



    B278819
  1. Remove the bolt and door side airbag sensor from the front door panel.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct



12. REMOVE FRONT DOOR SERVICE HOLE COVER


    B380649
  1. Remove the bolt.

  1. Disconnect each connector.

  1. Disengage the 5 clamps.

  1. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through the front door service hole cover.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the front door panel.



13. REMOVE NO. 1 FRONT DOOR SERVICE HOLE SEAL


    B380652
  1. Remove the No. 1 front door service hole seal.



14. REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL


    B380653
  1. Remove the No. 2 front door service hole seal.



15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B277200
  1. Remove the grommet.

  1. Connect the cable to the negative (-) battery terminal.

  1. for Driver Side:

    1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    2. Disconnect the power window regulator master switch assembly.

  1. for Front Passenger Side:

    1. Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    2. Disconnect the power window regulator switch assembly.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    B280340
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the front door glass sub-assembly to fall.



    B280342E02
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.



16. REMOVE FRONT DOOR GLASS RUN


    B281735
  1. Remove the front door glass run.



17. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B280349
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.



18. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    B280351
  1. Remove the hole plug.



    B280352
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



19. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    B372656E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.



  1. When reusing the front door lock with motor assembly:



      B280363
    1. Remove the door lock wiring harness seal from the front door lock with motor assembly.



20. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280364
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



21. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280366
  1. Using a screwdriver, disengage the 3 claws.



    B280367
  1. Remove the front door inside locking cable assembly as shown in the illustration.