REAR SEAT RECLINING CONTROL CABLE (for TMMK Made) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 4. REMOVE REAR SEAT CUSHION LOCK HOOK |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 5. REMOVE INNER LUGGAGE COMPARTMENT TRIM PAD |
![]() |
Remove the inner luggage compartment trim pad.
| 6. REMOVE REAR SEATBACK ASSEMBLY LH |
![]() |
Disengage the 2 fasteners as shown in the illustration.
| *a | Fastener |
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 7. REMOVE REAR SEATBACK ASSEMBLY RH |
![]() |
Disengage the 3 fasteners as shown in the illustration.
| *a | Fastener |
![]() |
Remove the 2 bolts and rear seatback assembly RH.
| 8. REMOVE REAR SIDE SEATBACK ASSEMBLY LH |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.
Disconnect the connector.
![]() |
Remove the 2 bolts.
Disengage the hook and remove the rear side seatback assembly LH.
| 9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.
Disconnect the connector.
![]() |
Remove the 2 bolts.
Disengage the hook and remove the rear side seatback assembly RH.
| 10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the rear door opening trim weatherstrip LH.
| 11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Disconnect the rear door opening trim weatherstrip RH.
| 12. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 14. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.
| 15. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
for Type A:
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.
for Type B:
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.
| 16. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
Remove the 5 clips from the roof side inner garnish LH.
| 17. REMOVE ROOF SIDE INNER GARNISH RH |
| 18. REMOVE CENTER STOP LIGHT SET |
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.
![]() |
Turn the center stop light set 180 degrees as shown by the arrow in the illustration.
Disconnect the connector and remove the center stop light set.
| 19. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.
| 20. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.
| 21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
| *a | Protective Tape |
Disengage the 5 guides.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
| 22. REMOVE ROOM PARTITION BOARD LH |
![]() |
Disengage the guide, 2 claws and 4 clips, and remove the room partition board LH.
| 23. REMOVE ROOM PARTITION BOARD RH |
![]() |
Using a clip remover, remove the 2 clips.
Disengage the 5 clips and remove the room partition board RH.
| 24. REMOVE REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH) |
![]() |
Disengage the hook as shown in the illustration.
![]() |
Remove the 2 nuts and rear seatback lock assembly LH (rear seat lock control cable LH).
| 25. REMOVE REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH) |