Home › Power Source / Network ยท POWER DISTRIBUTION › INTEGRATION RELAY

INTEGRATION RELAY > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (SIGNAL READING CHECK)

NOTICE:
Both present and history signal readings will be cleared if the engine room junction block assembly is removed. Make sure not to remove it before inspection.

HINT:
The signal readings of the engine room junction block assembly can be checked by inspecting the voltage at the diagnosis terminal.



  1. Signal reading check

    1. Turn the ignition switch to ON.



    2. E227859E01
    3. Connect the positive (+) terminal of a voltmeter to the engine room junction block assembly and the negative (-) terminal to the body ground.
      Text in Illustration 
      *a
      Component with harness connected
      (Engine Room Junction Block Assembly)
      *b
      Diagnosis Terminal



    4. Using the illustration below as a reference, determine whether any channels are malfunctioning based on the observed signal reading.


      E228235E01

      HINT:
      1. The present signal reading and history signal reading will be displayed alternately after the ignition switch is turned to ON. By measuring the duration of each header, the present signal reading and history signal reading can be recognized.
      2. A unit malfunction indicates an internal malfunction of the engine room junction block assembly. If a malfunction is detected for any channel from channel 0 to 9, an electrical load connected to the engine room junction block assembly may be malfunctioning or there may be a short in the engine room junction block assembly circuit or in the wire harness.
      3. The present signal reading will be stored as a history signal reading when electrical loads are operated after a malfunctioning part returns to normal.
      4. Both present and history signal readings can be cleared by disconnecting the cable from the negative (-) battery terminal.
      5. Depending on the specification, different electrical loads connected to channels 0 to 9 are provided. Refer to the table below:

        Channel
        Connected Electrical Load
        for 2AR-FE
        for 2GR-FE
        ch0
        Radiator fan motor
        Magnetic clutch
        ch1
        Condenser fan motor
        -
        ch2
        Mirror heater*1
        ch3
        -
        ch4
        Daytime running lights
        ch5
        Rear fog lights*2
        ch6
        Front fog lights*3
        ch7
        Rear window defogger wire
        ch8
        High beam headlight LH
        ch9
        High beam headlight RH
      1. *1: for TMC, TMMR Made
      1. *2: w/ Rear Fog Light
      1. *3: w/ Front Fog Light



2. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)


  1. Results of signal reading check

    1. Depending on the signal reading, perform troubleshooting according to the table below.

      Output Signal Reading
      Repair Method
      Normal
      Continue troubleshooting for each system.
      The unit is malfunctioning.
      Replace the engine room junction block assembly.
      A malfunction in a channel (ch0 to ch9)
      1. Check for a short in the wire harnesses between the engine room junction block assembly and each electrical load.
      2. Inspect each of the electrical loads.
      3. Replace the engine room junction block assembly.

      HINT:
      Make sure to clear the signal readings by disconnecting the cable from the negative (-) battery terminal after replacement or repair of the malfunctioning part.



    2. E231278E01
    3. If no signal readings are output, perform troubleshooting according to the following troubleshooting procedure.

      1. Remove the engine room junction block assembly (Click here).
      2. Measure the voltage according to the value(s) in the table below.

        Standard Voltage:
        Tester Connection
        Condition
        Specified Condition
        1F-15 (IGN) - Body ground
        Ignition switch ON
        11 to 14 V

        Text in Illustration 
        *a
        Component without engine room junction block assembly
        (Engine Room Junction Block Assembly)
        If the result is not as specified, repair or replace the wire harness or connector.