NOISE FILTER (for TMC, TMMR Made) > INSTALLATION |
| 1. INSTALL RADIO SETTING CONDENSER (for Window Defogger) |
![]() |
Engage the claw to install a new terminal cover to the wire harness.
![]() |
Engage the 3 claws to install the new terminal cover with wire harness to a new condenser.
Engage the 2 clamps to temporarily install a new radio setting condenser with wire harness.
Install the new radio setting condenser with the bolt.
| 2. INSTALL ROOF SIDE INNER GARNISH LH (for Window Defogger) |
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
| 3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger) |
| 4. INSTALL RADIO SETTING CONDENSER (for High Mounted Stop Light) |
![]() |
Engage the claw to install a new terminal cover to the wire harness.
![]() |
Engage the 6 claws to install the 2 new terminal covers with wire harness to a new condenser.
![]() |
Engage the claw to insert the cover as shown in the illustration.
Engage the clamp to temporarily install a new radio setting condenser with wire harness.
Install the new radio setting condenser with the bolt.
| 5. INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
Engage the guide, claw and 2 clips.
Install the rear seat side garnish LH with the bolt.
| 6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type) |
![]() |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *1 | Alignment Mark (Red) |
| 7. INSTALL REAR DOOR SCUFF PLATE LH (for Reclining Seat Type) |
Engage the 6 claws to install the rear door scuff plate LH.
| 8. INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.
| 9. INSTALL REAR SEATBACK COVER (for Reclining Seat Type) |
Engage the 4 claws to install the 2 rear seatback covers.
| 10. INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 11. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 12. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
Place the rear seat cushion assembly in the cabin.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.
Connect the 2 seat heater connectors.
![]() |
Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.
Confirm that the rear seat cushion assembly is securely installed.
| 13. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Place the rear side seatback assembly LH in the cabin.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.
| 14. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 15. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
Place the rear seat cushion assembly in the cabin.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the connector.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
| 16. INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
| 17. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 19. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag) |