NOISE FILTER (for TMC, TMMR Made) > REMOVAL |
| 1. PRECAUTION (w/ Rear Seat Side Airbag) |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 3. REMOVE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
| 4. REMOVE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
| 5. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
w/ Seat Heater System:
Disconnect the connector.
![]() |
Disengage the 2 clamps.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 6. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
Disconnect the 2 seat heater connectors.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 9. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 10. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 11. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 12. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 13. REMOVE REAR DOOR SCUFF PLATE LH (for Reclining Seat Type) |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 14. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type) |
Disconnect the rear door opening trim weatherstrip LH.
| 15. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 16. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light) |
![]() |
Remove the bolt.
Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
![]() |
Disengage the claw and pull out the cover as shown in the illustration.
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser.
![]() |
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Remove the terminal cover from the wire harness.
| 17. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger) |
| 18. REMOVE ROOF SIDE INNER GARNISH LH (for Window Defogger) |
![]() |
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
| 19. REMOVE RADIO SETTING CONDENSER (for Window Defogger) |
![]() |
Remove the bolt.
Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.
![]() |
Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.
![]() |
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Remove the terminal cover from the wire harness.