Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RECEIVER (for TMC, TMMR Made)

DOOR CONTROL RECEIVER (for TMC, TMMR Made) > INSTALLATION

for Preparation Click here



1. INSTALL DOOR CONTROL RECEIVER
  1. Install the door control receiver with the bolt.

  1. Connect the connector.



2. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and LH side .



3. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
  1. Place the rear side seatback assembly RH in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Engage the hook to install the rear side seatback assembly RH with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.



4. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    B393388
  1. Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



5. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. w/ Seat Heater System:

    1. Engage the 2 clamps.

    2. Connect the connector.



    B383049
  1. Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is firmly installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.



6. INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
  1. w/ Seat Heater System:



7. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
  1. w/ Seat Heater System:



8. INSTALL REAR SEAT SIDE GARNISH RH (for Reclining Seat Type)

HINT:
Use the same procedure for the RH side and LH side .



9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B278983E01
  1. Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *1
    Alignment Mark (Blue)

    NOTICE:
    After installation, check that the corners fit correctly.



10. INSTALL REAR DOOR SCUFF PLATE RH (for Reclining Seat Type)

HINT:
Use the same procedure for the RH side and LH side .



11. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    B393388
  1. Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



12. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.

  1. Connect the 2 seat heater connectors.



    B290775
  1. Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is securely installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.



13. REGISTER DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY ID (w/o Smart Entry and Start System)

HINT:
In case of door control receiver replacement (Click here).