Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM


E302845E01


E302846E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)
  1. Disconnect the I68 stereo component amplifier assembly connector.

  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I60 front No. 3 speaker assembly connector.

  1. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.

  1. Disconnect the O22 rear speaker assembly connector.

  1. Disconnect the I84 and I2 front No. 2 speaker assembly connectors.

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).



    E289435E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 2 (-)
    Always
    4.6 to 6.6 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY
  1. Remove the front No. 3 speaker assembly (Click here).



    E222247E33
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6.8 to 10.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
  1. Remove the rear No. 2 speaker assembly (Click here).



    E222247E33
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6.8 to 10.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).



    E289435E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4.8 to 6.8 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).



    E180660E50
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 - 3
    Always
    3.4 to 5.2 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


7.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both the LH and RH side.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK

END