NAVIGATION SYSTEM (for Navigation Receiver Type) > Speaker Circuit |
| for TMC Made |

| for TMMK Made |


| 1.CHECK MODEL |
Choose the model to be inspected.
| Result | Proceed to |
| for TMC Made | A |
| for TMMK Made | B |
|
| ||||
| A | |
| 2.CHECK SPEAKER (OPERATION CHECK) |
![]() |
Enter the "System Check Mode" screen.
Refer to Check Speaker in Operation Check (Click here).
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the I64 navigation receiver assembly connector.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Measure the resistance between the navigation receiver assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I64-1 (FR+) - I83-4 (TWR+) | Always | Below 1 Ω |
| I64-5 (FR-) - I83-2 (TWR-) | Always | Below 1 Ω |
| I64-2 (FL+) - I1-4 (TWL+) | Always | Below 1 Ω |
| I64-6 (FL-) - I1-2 (TWL-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 2 speaker assemblies and the front No. 1 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I83-3 (+) - J5-1 | Always | Below 1 Ω |
| I83-1 (-) - J5-2 | Always | Below 1 Ω |
| I1-3 (+) - K5-1 | Always | Below 1 Ω |
| I1-1 (-) - K5-2 | Always | Below 1 Ω |
Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I64-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I64-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I64-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I64-6 (FL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I83-3 (+) - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (TWR+) - 2 (TWR-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWR+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWR-) | Always | Below 1 Ω |
| 4 (TWL+) - 2 (TWL-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWL+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWL-) | Always | Below 1 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the malfunction disappears when a new or known good speaker is installed (Click here).
|
| ||||
| OK | ||
| ||
| 6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the I65 navigation receiver assembly connector.
Disconnect the O18 and O21 rear speaker assembly connectors.
Measure the resistance between the navigation receiver assembly and each of the rear speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I65-1 (RR+) - O18-1 | Always | Below 1 Ω |
| I65-3 (RR-) - O18-2 | Always | Below 1 Ω |
| I65-2 (RL+) - O21-1 | Always | Below 1 Ω |
| I65-6 (RL-) - O21-2 | Always | Below 1 Ω |
Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I65-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I65-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I65-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I65-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 9.CHECK SPEAKER (OPERATION CHECK) |
![]() |
Enter the "System Check Mode" screen.
Refer to Check Speaker in Operation Check (Click here).
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 3 speaker assembly | C |
| Rear No. 2 speaker assembly | D |
| Rear speaker assembly | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the front No. 1 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) - J5-1 (+) | Always | Below 1 Ω |
| I68-30 (FR-) - J5-2 (-) | Always | Below 1 Ω |
| I68-11 (FL+) - K5-1 (+) | Always | Below 1 Ω |
| I68-26 (FL-) - K5-2 (-) | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 2 (-) | Always | 4.6 to 6.6 Ω |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-12 (TWR+) - I84-4 | Always | Below 1 Ω |
| I68-27 (TWR-) - I84-3 | Always | Below 1 Ω |
| I68-14 (TWL+) - I2-4 | Always | Below 1 Ω |
| I68-29 (TWL-) - I2-3 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-12 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 - 3 | Always | 3.4 to 5.2 Ω |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 14.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the malfunction disappears when a known good speaker is installed (Click here).
|
| ||||
| OK | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I60 front No. 3 speaker assembly connector.
Measure the resistance between the stereo component amplifier assembly and the front No. 3 speaker assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-13 (CTR+) - I60-2 | Always | Below 1 Ω |
| I68-28 (CTR-) - I60-1 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-13 (CTR+) - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 16.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
Remove the front No. 3 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| *a | Component without harness connected (Front No. 3 Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and each of the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-10 (SR+) - O19-2 | Always | Below 1 Ω |
| I68-25 (SR-) - O19-1 | Always | Below 1 Ω |
| I68-9 (SL+) - O20-2 | Always | Below 1 Ω |
| I68-24 (SL-) - O20-1 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-10 (SR+) - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
Remove the rear No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| *a | Component without harness connected (Rear No. 2 Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O22 rear speaker assembly connector.
Measure the resistance between the stereo component amplifier assembly and the rear speaker assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-8 (WF1+) - O22-1 | Always | Below 1 Ω |
| I68-23 (WF1-) - O22-2 | Always | Below 1 Ω |
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 20.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4.8 to 6.8 Ω |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||