NAVIGATION SYSTEM (for Radio and Display Type) > Speaker Circuit |


| 1.CHECK SPEAKER (OPERATION CHECK) |
![]() |
Enter the "System Check Mode" screen.
Refer to Check Speaker in Operation Check (Click here).
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
| Front No. 1 speaker assembly | A |
| Front No. 3 speaker assembly | B |
| Front No. 2 speaker assembly | C |
| Rear No. 2 speaker assembly | D |
| Rear speaker assembly | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) - J5-1 (+) | Always | Below 1 Ω |
| I68-30 (FR-) - J5-2 (-) | Always | Below 1 Ω |
| I68-11 (FL+) - K5-1 (+) | Always | Below 1 Ω |
| I68-26 (FL-) - K5-2 (-) | Always | Below 1 Ω |
| I68-15 (FR+) or J5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) or J5-2 (-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) or K5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) or K5-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I60 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-13 (CTR+) - I60-2 | Always | Below 1 Ω |
| I68-28 (CTR-) - I60-1 | Always | Below 1 Ω |
| I68-13 (CTR+) or I60-2 - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) or I60-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
Remove the front No. 3 speaker assembly (Click here).
Inspect the front No. 3 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-12 (TWR+) - I84-4 | Always | Below 1 Ω |
| I68-27 (TWR-) - I84-3 | Always | Below 1 Ω |
| I68-14 (TWL+) - I2-4 | Always | Below 1 Ω |
| I68-29 (TWL-) - I2-3 | Always | Below 1 Ω |
| I68-12 (TWR+) or I84-4 - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) or I84-3 - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) or I2-4 - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) or I2-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
Inspect the front No. 2 speaker assembly (Click here).
Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-10 (SR+) - O19-2 | Always | Below 1 Ω |
| I68-25 (SR-) - O19-1 | Always | Below 1 Ω |
| I68-9 (SL+) - O20-2 | Always | Below 1 Ω |
| I68-24 (SL-) - O20-1 | Always | Below 1 Ω |
| I68-10 (SR+) or O19-2 - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) or O19-1 - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) or O20-2 - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) or O20-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
Remove the rear No. 2 speaker assembly (Click here).
Inspect the rear No. 2 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O22 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-8 (WF1+) - O22-1 | Always | Below 1 Ω |
| I68-23 (WF1-) - O22-2 | Always | Below 1 Ω |
| I68-8 (WF1+) or O22-1 - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) or O22-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
Inspect the rear speaker assembly (Click here).
|
| ||||
| OK | ||
| ||