Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B150A    Lost Communication with HMI-LAN

for Preparation Click here


DESCRIPTION

The combination meter assembly receives a text data signal from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.
Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.
This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No.
DTC Detection Condition
Trouble Area
B150A
After the combination meter assembly receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the ignition switch is ACC, 1 or more times, the combination meter assembly does not receive the signal for 30 seconds or more.
  1. Harness or connector
  2. Navigation receiver assembly*1
  3. Radio and display receiver assembly*2
  4. Combination meter assembly
  1. *1: for Navigation Receiver Type
  2. *2: for Radio and Display Type

WIRING DIAGRAM


for Navigation Receiver Type

E274272E09


for Radio and Display Type

E274272E25


INSPECTION PROCEDURE

1.CONFIRM VEHICLE TYPE
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for Navigation Receiver Type
    A
    for Radio and Display Type
    B



B
Go to step 5
A


2.CHECK FOR DTC
  1. Check if navigation system DTCs are output (Click here).

    Result:
    Result
    Proceed to
    Navigation system DTCs are not output.
    A
    Navigation system DTCs are output.
    B



B
GO TO NAVIGATION SYSTEM (Click here)
A


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the I18 combination meter assembly connector.

  1. Disconnect the I184 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-19 (MSCL) - I184-4 (CNL1)
    Always
    Below 1 Ω
    I18-18 (MSCH) - I184-3 (CNH1)
    Always
    Below 1 Ω
    I18-19 (MSCL) - Body ground
    Always
    10 kΩ or higher
    I18-18 (MSCH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or known good one (Click here).

  1. Turn the ignition switch to ON and wait 30 seconds.

    NOTICE:
    A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly.

  1. Operate the steering pad switch assembly and check that the navigation tab illuminates.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    The navigation tab illuminates and DTC B150A is not output.
    A
    The navigation tab does not illuminate and DTC B150A is output (except TMMK Made).
    B
    The navigation tab does not illuminate and DTC B150A is output (for TMMK Made).
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END 

5.CHECK FOR DTC
  1. Check if navigation system*1 or audio and visual system*2 DTCs are output (Click here with Navigation System, Click here without Navigation System).

    Result:
    Result
    Proceed to
    DTCs are not output.
    A
    Navigation system DTCs are output*1.
    B
    Audio and visual system DTCs are output*2.
    C

    1. *1: w/ Navigation System
    2. *2: w/o Navigation System



B
GO TO NAVIGATION SYSTEM (Click here)

C
GO TO AUDIO AND VISUAL SYSTEM (Click here)
A


6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
  1. Disconnect the I18 combination meter assembly connector.

  1. Disconnect the I185 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-19 (MSCL) - I185-4 (CNL1)
    Always
    Below 1 Ω
    I18-18 (MSCH) - I185-3 (CNH1)
    Always
    Below 1 Ω
    I18-19 (MSCL) - Body ground
    Always
    10 kΩ or higher
    I18-18 (MSCH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or known good one (Click here).

  1. Turn the ignition switch to ON and wait 30 seconds.

    NOTICE:
    A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver assembly.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B150A is not output.
    A
    DTC B150A is output (except TMMK Made).
    B
    DTC B150A is output (for TMMK Made).
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A

END