DTC B150A Lost Communication with HMI-LAN |
| DTC No. | DTC Detection Condition | Trouble Area |
| B150A | After the combination meter assembly receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the ignition switch is ACC, 1 or more times, the combination meter assembly does not receive the signal for 30 seconds or more. |
|
| for Navigation Receiver Type |

| for Radio and Display Type |

| 1.CONFIRM VEHICLE TYPE |
Choose the model to be inspected.
| Result | Proceed to |
| for Navigation Receiver Type | A |
| for Radio and Display Type | B |
|
| ||||
| A | |
| 2.CHECK FOR DTC |
Check if navigation system DTCs are output (Click here).
| Result | Proceed to |
| Navigation system DTCs are not output. | A |
| Navigation system DTCs are output. | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY) |
Disconnect the I18 combination meter assembly connector.
Disconnect the I184 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-19 (MSCL) - I184-4 (CNL1) | Always | Below 1 Ω |
| I18-18 (MSCH) - I184-3 (CNH1) | Always | Below 1 Ω |
| I18-19 (MSCL) - Body ground | Always | 10 kΩ or higher |
| I18-18 (MSCH) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.REPLACE COMBINATION METER ASSEMBLY |
Replace the combination meter assembly with a new or known good one (Click here).
Turn the ignition switch to ON and wait 30 seconds.
Operate the steering pad switch assembly and check that the navigation tab illuminates.
Check for DTCs (Click here).
| Result | Proceed to |
| The navigation tab illuminates and DTC B150A is not output. | A |
| The navigation tab does not illuminate and DTC B150A is output (except TMMK Made). | B |
| The navigation tab does not illuminate and DTC B150A is output (for TMMK Made). | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FOR DTC |
Check if navigation system*1 or audio and visual system*2 DTCs are output (Click here with Navigation System, Click here without Navigation System).
| Result | Proceed to |
| DTCs are not output. | A |
| Navigation system DTCs are output*1. | B |
| Audio and visual system DTCs are output*2. | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
Disconnect the I18 combination meter assembly connector.
Disconnect the I185 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-19 (MSCL) - I185-4 (CNL1) | Always | Below 1 Ω |
| I18-18 (MSCH) - I185-3 (CNH1) | Always | Below 1 Ω |
| I18-19 (MSCL) - Body ground | Always | 10 kΩ or higher |
| I18-18 (MSCH) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.REPLACE COMBINATION METER ASSEMBLY |
Replace the combination meter assembly with a new or known good one (Click here).
Turn the ignition switch to ON and wait 30 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B150A is not output. | A |
| DTC B150A is output (except TMMK Made). | B |
| DTC B150A is output (for TMMK Made). | C |
|
| ||||
|
| ||||
| A | ||
| ||