ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > Engine does not Start but Initial Combustion Occurs |

| 1.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2.CHECK FOR DTC |
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs are not output | A |
| DTCs are output | B |
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Immobiliser Fuel Cut | Status of immobiliser fuel cut / ON or OFF | - | - |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 4.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 5.CHECK ECM (TERMINAL IMI) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (ECM) | *b | Component with harness connected (Transponder Key ECU Assembly) |
| *c | Waveform 1 | *d | Waveform 2 |
| *e | Approximately 160 ms | *f | Approximately 270 ms |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A25-28 (IMI) - I19-13 (EFIO) | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform) |
| Result | Proceed to |
| Normal waveform | A |
| Waveform 1 not output, or has abnormal wavelength or shape | B |
| Waveform 2 not output, or has abnormal wavelength or shape | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK ECM (TERMINAL IMO) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (ECM) | *b | Component with harness connected (Transponder Key ECU Assembly) |
| *c | Waveform | *d | Approximately 160 ms |
| *e | Approximately 270 ms | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A25-29 (IMO) - I19-12 (EFII) | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform) |
| Result | Proceed to |
| Normal waveform | A |
| Waveform not output, or has abnormal wavelength or shape | B |
|
| ||||
| A | |
| 7.REGISTER ECU COMMUNICATION ID |
Register the communication ID between the transponder key ECU assembly and ECM.
| NEXT | |
| 8.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
|
| ||||
| OK | ||
| ||
| 9.REPLACE ECM |
Temporarily replace the ECM with a new one (Click here).
| NEXT | |
| 10.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 11.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM) |
Disconnect the I19 transponder key ECU assembly connector.
Disconnect the A25 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-13 (EFIO) - A25-28 (IMI) | Always | Below 1 Ω |
| I19-13 (EFIO) or A25-28 (IMI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Replace the transponder key ECU assembly with a new one.
| NEXT | |
| 14.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
|
| ||||
| OK | ||
| ||