Home › Engine / Hybrid System ยท 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P1603    Engine Stall History

for Preparation Click here


DESCRIPTION

After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No.
DTC Detection Condition
P1603
After monitoring for startability problems (P1604) finishes and 2 seconds or more have elapsed after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).

Trouble Area
Ignition system
  1. Spark plug
  2. Ignition coil assembly
Fuel system
  1. Fuel injector assembly
  2. Fuel pump
  3. Fuel pump control circuit
  4. Fuel line
  5. Purge VSV system
  6. Fuel quality (existence of foreign matter, degradation)
Intake and exhaust systems
  1. Mass air flow meter sub-assembly
  2. Intake system (Air leaks or deposit accumulation)
  3. Throttle body with motor assembly
  4. Air fuel ratio sensor
  5. Heated oxygen sensor
  6. Camshaft timing oil control valve assembly
  7. Variable Valve Timing system (VVT system)
  8. Brake booster assembly
Other control systems
  1. ECM
  2. Wire harness or connector
  3. Knock control sensor
  4. Engine coolant temperature sensor
Engine
  1. Thermostat
  2. Engine assembly
  3. Engine mount
High load from another system
  1. Air conditioning system
  2. Power steering system
  3. Electrical load signal system
  4. A/T system

INSPECTION PROCEDURE

HINT:
  1. DTC P1603
    1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1603 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
      As this DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
    1. As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.
    1. DTCs related to engine stall problems may be detected due to operations performed by the user. The following are a few examples. Ask questions to the user about how the vehicle is operated and give advice as necessary.
      1. Ran out of fuel
      1. Rolled down on a slope and engine stalls (backed up in D, moved forward in R)
    1. If any other DTCs are output, perform troubleshooting for those DTCs first.
  2. CUSTOMER PROBLEM ANALYSIS
    1. Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

      Symptom
      Suspected Area
      Engine vibration occurs and engine stops
      1. Abnormal mass air flow meter sub-assembly output due to existence of foreign matter
      2. Abnormal air fuel ratio due to malfunction of air fuel ratio sensor or heated oxygen sensor, air leaks in intake system or insufficient fuel supply
      Engine stops with no engine vibration
      Ignition system, injection stoppage, high load from external parts
      Engine can be started with accelerator pedal depressed
      Insufficient air volume
      Engine stalls or is difficult to start immediately after engine stalled, regardless of whether engine is cold or warm
      Deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve
  3. FREEZE FRAME DATA
    1. Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
    1. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
    1. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
    1. Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare this data with the freeze frame data.
  4. PRECAUTIONS
    1. Inspections take into account the fact that the malfunction may not have recurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
    1. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

1.CHECK FOR ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    Only DTC P1603 is output
    A
    DTCs other than P1603 are output
    B

    HINT:
    1. When DTC P1603 and P1605 are output simultaneously, perform the troubleshooting for P1605 first.
    2. Using freeze frame data, confirm the conditions the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.



B
GO TO DTC CHART (Click here)
A


2.READ FREEZE FRAME DATA (ISC LEARNING VALUE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item for DTC P1603
    Result
    Suspected Area
    Action
    Proceed to
    ISC Learning Value
    Less than 8.5 L/s
    -
    Go to the next step
    A
    8.5 L/s or higher
    Throttle body with motor assembly
    Go to Engine Stalls (from step 11)
    B



B
GO TO ENGINE STALLS (Click here)
A


3.READ FREEZE FRAME DATA (AFS VOLTAGE B1S1 (B2S1), SHORT FT #1 (#2) AND LONG FT #1 (#2))
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item for DTC P1603
    Suspected Area
    Action
    Proceed to
    AFS Voltage B1S1 (B2S1)
    Short FT #1 (#2)
    Long FT #1 (#2)
    3.8 V or higher
    15% or higher
    -
    Fuel pump
    Go to Engine Stalls (from step 20)
    NEXT
    Less than 2.8 V, or 3.8 V or higher
    Less than -15%, or 15% or higher
    Less than -15%, or 15% or higher
    1. Mass air flow meter sub-assembly
    2. Air fuel ratio sensor
    3. Fuel pump
    Go to Engine Stalls (from step 15)*
    2.8 V to 3.8 V
    -15% to 15%
    -15% to 15%
    -
    Go to Engine Stalls

    HINT:
    *: If the value of AFS Voltage B1S1 (B2S1), Short FT #1 (#2) or Long FT #1 (#2) is as specified, malfunction of a component listed in the "Suspected Area" column of the table is suspected.


NEXT

GO TO ENGINE STALLS (Click here)