SFI SYSTEM > Engine Stalls |
| Problem Symptom | Suspected Area | Trouble Area | |
|
| Ignition system |
|
| Fuel system |
| ||
| Intake and exhaust systems |
| ||
| Other control systems |
| ||
| Engine |
| ||
| High load from another system |
| ||
| SYMPTOM AND CAUSE OF SYSTEM MALFUNCTION |
Ignition system
| Main cause of malfunction | Performance degradation (wear, existence of foreign matter, etc.) |
| Symptom | Engine speed fluctuation due to abnormal combustion |
| Data List | Cylinder #1 Misfire Count to Cylinder #6 Misfire Count |
| |
| Main cause of malfunction | Internal malfunction |
| Problem symptom | Engine speed fluctuation due to abnormal combustion |
| Data List | Cylinder #1 Misfire Count to Cylinder #6 Misfire Count |
Fuel system
| Main cause of malfunction | Blockage |
| Problem symptom |
|
| Data List |
|
| |
| Main cause of malfunction | Purge VSV stuck open |
| Symptom | Engine speed fluctuation due to abnormal combustion |
| Data List |
|
|
| Main cause of malfunction |
|
| Problem symptom |
|
Intake and exhaust systems
| Main cause of malfunction | Performance degradation (existence of foreign matter, etc.) |
| Problem symptom | Lack of power |
| Data List | MAF |
| |
| Main cause of malfunction | Inappropriate trim volume adjustment due to accumulation of deposits |
| Problem symptom |
|
| Data List |
|
| Main cause of malfunction | Deviation in sensor characteristics |
| Problem symptom | Abnormal combustion due to deviation of actual air fuel ratio from calculated ratio |
| Data List |
|
Engine
| Main cause of malfunction |
|
| Problem symptom |
|
| Data List |
|
| |
| Main cause of malfunction | Camshaft timing oil control valve assembly stuck open |
| Symptom | Abnormal combustion due to excessive valve overlap |
| Data List |
|
| Data List Items Related to Engine Stalls |
| 1.INTERVIEW THE CUSTOMER |
Interview the customer for details about the conditions when the engine stalled.
| Symptom | Suspected Area |
| Engine vibration occurs and engine stalls |
|
| Engine stalls without vibration | Ignition stoppage, fuel injection stoppage or high load from another system |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Engine stalls or is difficult to start immediately after engine stalled, regardless of whether engine is cold or warm | Deposits in intake system or combustion chamber caught temporarily on intake or exhaust valve |
| NEXT | |
| 2.CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC is output (DTCs other than P1603, P1604 or P1605 are output) | B |
|
| ||||
| A | |
| 3.SYMPTOM CONFIRMATION |
Check if the problem symptoms reported in the customer problem analysis recur.
| Result | Proceed to |
| The problem symptom recurs | A |
| The problem symptom does not recur (occurred in the past) | B |
|
| ||||
| A | |
| 4.READ VALUE USING GTS (ISC LEARNING VALUE) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / ISC Learning Value.
Read the value displayed on the GTS.
| Result | Proceed to |
| Less than 8.5 L/s | A |
| Other than above | B |
|
| ||||
| A | |
| 5.READ VALUE USING GTS (SHORT FT #1 (#2) AND LONG FT #1 (#2)) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Short FT #1 (#2) and Long FT #1 (#2).
Read the value displayed on the GTS.
| Data List | Result | Proceed to |
| Short FT #1 (#2) + Long FT #1 (#2) | -15% or higher, or less than 15% | A |
| Other than above | B |
|
| ||||
| A | |
| 6.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut / Data List / All Data / Engine Speed.
According to the display on the GTS, perform the Active Test and check for a malfunctioning cylinder.
| Result | Proceed to |
| One cylinder is malfunctioning | A |
| Multiple or all cylinders are malfunctioning, or the malfunctioning cylinder cannot be determined | B |
|
| ||||
| A | |
| 7.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #6 and Av Engine Speed of All Cyl.
While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
Crank the engine for about 10 seconds.
Monitor the engine speed (Engine Speed of Cyl #1 to #6 and Av Engine Speed of All Cyl) displayed on the GTS.
Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
Read the value.
| Result | Proceed to |
| There is no variation in "Engine Speed of Cyl #1 to #6" (All cylinders display approximately the same value for "Engine Speed of Cyl #1 to #6") | A |
| There is variation in "Engine Speed of Cyl #1 to #6" (Only one cylinder displays a value for "Engine Speed of Cyl #1 to #6" that differs considerably) | B |
|
| ||||
| A | |
| 8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
According to the display on the GTS, perform the Active Test and check the vehicle conditions when increasing and decreasing the fuel injection volume.
| Result | Proceed to |
| Malfunction is still present even if the fuel injection volume is changed | A |
| Malfunction disappears when the fuel injection volume is changed | B |
|
| ||||
| A | |
| 9.CHECK IGNITION SYSTEM |
Check the ignition system.
| Result | Proceed to |
| The malfunctioning cylinder does not return to normal | A |
| The malfunctioning cylinder returned to normal | B |
|
| ||||
| A | |
| 10.INSPECT OTHER RELATED COMPONENTS |
Check the power source circuit, wire harness and connectors.
|
| ||||
| 11.REMOVE FOREIGN OBJECT (CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY) |
![]() |
Clean off any deposits from the inside of the throttle body with motor assembly.
Push open the throttle valve and wipe off any carbon from the valve and bore using a piece of cloth soaked in non-residue solvent.
| *1 | Bore |
| *2 | Valve |
| *a | Reference |
| *b | Throttle Body with Motor Assembly Cross-section Diagram |
| *c | When valve fully opened |
| *d | Deposits |
| *e | Do not directly apply cleaner |
| NEXT | |
| 12.PERFORM CONFIRMATION DRIVING PATTERN |
Perform "Inspection After Repair" after cleaning the throttle body with motor assembly (Click here).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Allow the engine to idle for 3 minutes or more and confirm that the engine speed is within the specified range.
|
| ||||
| 13.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure. If the compression pressure of a cylinder is low, inspect the engine assembly and repair or replace parts as necessary .
|
| ||||
| 14.REPLACE FUEL INJECTOR ASSEMBLY |
Replace the fuel injector assembly of the malfunctioning cylinder (Click here).
|
| ||||
| 15.READ VALUE USING GTS (MAF) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.
Enter the following menus: Powertrain / Engine / Data List / All Data / MAF.
According to the display on the GTS, read the Data List when the engine switch is turned on (IG) and while maintaining an engine speed of 2500 rpm.
| Result | Proceed to |
| Other than below | A |
| Engine switch on (IG) (engine stopped): 0.49 gm/sec or higher Engine speed 2500 rpm (without load): Less than 8 gm/sec | B |
|
| ||||
| A | |
| 16.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Idle the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2.
According to the display on the GTS, perform the Active Test and check the vehicle conditions when increasing and decreasing the fuel injection volume.
| GTS Display (Sensor) | Injection Volume | Voltage |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | 12.5% | Below 3.1 V |
| -12.5% | Higher than 3.4 V | |
| O2S B1S2 O2S B2S2 (Heated oxygen) | 12.5% | Higher than 0.55 V |
| -12.5% | Below 0.4 V |
| Result | Proceed to |
| Output voltage values are abnormal | A |
| Malfunction disappears when fuel injection volume is increased | B |
| Malfunction is still present when fuel injection volume is increased, even if output voltage values are normal | C |
|
| ||||
|
| ||||
| A | |
| 17.REPLACE AIR FUEL RATIO SENSOR AND HEATED OXYGEN SENSOR |
Replace the air fuel ratio sensor (Click here).
Replace the heated oxygen sensor (Click here).
|
| ||||
| 18.REPLACE FUEL INJECTOR ASSEMBLY |
Replace the fuel injector assemblies of all cylinders (Click here).
|
| ||||
| 19.CHECK INTAKE SYSTEM |
Check for air leaks or blockage in the intake system components. If a connection problem or foreign matter is found, repair the connection or remove the foreign matter.
|
| ||||
| 20.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
|
| ||||
| OK | |
| 21.INSPECT FUEL PUMP |
Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine .
| Vehicle State | Specified Condition |
| Cranking engine | 380 to 420 kPa (3.9 to 4.3 kgf/cm2, 55 to 61 psi) |
| 5 minutes after stopping engine | 147 kPa (1.5 kgf/cm2, 21 psi) or higher |
|
| ||||
| OK | |
| Go to step 24 |
| 22.INSPECT OTHER RELATED COMPONENTS |
Inspect other related components.
|
| ||||
| 23.INSPECT RELATED PARTS |
Inspect the following fuel pump related parts:
|
| ||||
| 24.INSPECT FUEL PUMP CONTROL SYSTEM |
Inspect the fuel pump control system (Click here).
| NEXT | |
| 25.REPAIR OR REPLACE MALFUNCTIONING PARTS |
Repair or replace the malfunctioning part.
Perform "Inspection After Repair" after repairing or replacing the malfunctioning part (Click here).
| NEXT | |
| 26.CONDUCT CONFIRMATION TEST |
Check that the idle has returned to normal.
| NEXT | ||
| ||