Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P019015    Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open

for Preparation Click here


DESCRIPTION

Refer to DTC P019011 .

DTC No.
DTC Detection Condition
Trouble Area
P019015
The fuel pressure sensor output voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor
  3. ECM

HINT:
When this DTC is output, check the fuel pressure (for high pressure side) in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).


DTC No.
Fuel Pressure (High)
Malfunction
P019015
Approximately 32000 kPag or higher
  1. Short in VCPR to PR circuit
  2. Open in PR circuit
  3. Open in EPR circuit
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

This DTC is stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.
  1. Example:
    1. If the fuel pressure sensor output voltage is higher than 4.9 V for 3 seconds or more, the ECM store this DTC.

MONITOR STRATEGY


Required Sensors/Components
Fuel pressure sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine.
  7. Idle the engine for 10 seconds.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P019015.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P019011 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
G2-3 (PR) - E96-103 (PR)
Always
Below 1 Ω
G2-2 (E2) - E96-135 (EPR)
Always
Below 1 Ω
G2-3 (PR) or E96-103 (PR) - Other terminals
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PRESSURE SENSOR)
A332083E01
  1. Disconnect the fuel pressure sensor connector.

Text in Illustration 
*a
Front view of wire harness connector
(to Fuel Pressure Sensor)
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
G2-1 (VC) - G2-2 (E2)
Engine switch on (IG)
4.75 to 5.25 V



NG
REPLACE ECM (Click here)
OK

REPLACE FUEL DELIVERY PIPE (FUEL PRESSURE SENSOR) (Click here)