DTC P070513 Transmission Range Sensor "A" Circuit Open |
DTC P070562 Transmission Range Sensor "A" Signal Compare Failure |
| DTC No. | DTC Detection Condition | Trouble Area |
| P070513 | All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic). |
|
| P070562 | Either of the following condition A or B is met (2 trip detection logic): A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more: (a) Any 2 or more of the following signals are on simultaneously:
|
|
| Required Sensors/Components | Park/Neutral position switch assembly |
| Frequency of Operation | Continuous |
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| DATA LIST |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (S Range) and Shift SW Status (D Range).
Read the Data List displayed on the GTS.
| GTS Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift SW Status (R Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (P Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| Shift SW Status (S Range) | Transmission control switch status: ON or OFF |
| - |
| Shift SW Status (D Range) | Park/Neutral position switch assembly status: ON or OFF |
| When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect |
| 1.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW and Shift SW Status (P, R, N and D Range).
Read the Data List displayed on the GTS.
| GTS Display | Shift Lever Position | Specified Condition |
| Neutral Position SW | P or N | ON |
| Except P or N | OFF | |
| Shift SW Status (P Range) | P | ON |
| Except P | OFF | |
| Shift SW Status (R Range) | R | ON |
| Except R | OFF | |
| Shift SW Status (N Range) | N | ON |
| Except N | OFF | |
| Shift SW Status (D Range) | D or S | ON |
| Except D or S | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE)) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (S Range).
Read the Data List displayed on the GTS.
| GTS Display | Shift Lever Position | Specified Condition |
| Shift SW Status (S Range) | S | ON |
| Except S | OFF |
|
| ||||
| OK | ||
| ||
| 3.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) |
Inspect the transmission control switch .
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
Disconnect the transmission control switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I44-5 (S) - A84-59 (S) | Always | Below 1 Ω |
| I44-5 (S) or A84-59 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY) |
![]() |
Disconnect the park/neutral position switch assembly connector.
| *a | Front view of wire harness connector (to Park/Neutral Position Switch Assembly) |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E85-1 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
|
| ||||
| OK | |
| 6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E85-7 (DL) - E96-34 (D) | Always | Below 1 Ω |
| E85-8 (NL) - E96-65 (N) | Always | Below 1 Ω |
| E85-2 (RL) - E96-35 (R) | Always | Below 1 Ω |
| E85-3 (PL) - E96-64 (P) | Always | Below 1 Ω |
| E85-4 (B) - A84-57 (NSW) | Always | Below 1 Ω |
| E85-7 (DL) or E96-34 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| E85-8 (NL) or E96-65 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| E85-2 (RL) or E96-35 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| E85-3 (PL) or E96-64 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| E85-4 (B) or A84-57 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||