DTC P160500 Rough Idling |
| DTC No. | DTC Detection Condition |
| P160500 | When idling with the accelerator pedal released and the vehicle stopped, this item detects when the combustion is worsening at predetermined levels from the changes in engine speed between the cylinders. Detection for 2 to 10 seconds according to the combustion state. (1 trip detection logic). |
| Trouble Area | |
| Ignition system |
|
| Fuel system |
|
| Intake and exhaust systems |
|
| Other control systems |
|
| Engine |
|
| High load from another system |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| Only DTC P160500 is output | A |
| DTCs other than P160500 are output | B |
|
| ||||
| A | |
| 2.READ FREEZE FRAME DATA |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P160500 | Suspected Area | Action | Proceed to | |
| Compression Leakage Count | |||
| "One of Rough Idle Cylinder #1 to #4 is ON" and "Plural Cylinders Rough Idle is OFF" | 0 |
| Go to ROUGH IDLING (from step 8) | A |
| Plural Cylinders Rough Idle is ON | 0 |
| Go to the next step | B |
| "One of Rough Idle Cylinder #1 to #4 are ON" or "Plural Cylinders Rough Idle is ON" | 1 or more | Pressure loss from valve damage, deposits jamming the valve etc. | Check compression and clean deposits in combustion chamber and intake system. | C |
|
| ||||
|
| ||||
| A | |
| 3.DETERMINE CAUSE OF MALFUNCTION FOR INDIVIDUAL CYLINDER |
Perform troubleshooting from Rough Idling step 8 (PERFORM ACTIVE TEST USING GTS (D-4S (INJECTION VOLUME))) and onward .
| NEXT | ||
| ||
| 4.READ FREEZE FRAME DATA (CALCULATE LOAD) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item for DTC P160500 | Result | Suspected Area | Action | Proceed to |
| Calculate Load | +10% or higher of the normal value of the vehicle | EGR valve assembly | Go to ROUGH IDLING (from step 15) | NEXT |
| Less than 10% of the normal value of the vehicle | - | Go to ROUGH IDLING |
| NEXT | ||
| ||
| 5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed Cylinder #1 to #4 and Average Engine Speed of All Cylinder.
While the engine is not running, press the Active Test button to change Check the Cylinder Compression to "Start".
Crank the engine for about 10 seconds.
Monitor the engine speed (Engine Speed Cylinder #1 to #4 and Average Engine Speed of All Cylinder) displayed on the GTS.
Stop cranking the engine, and then change "Check the Cylinder Compression" to "Stop" after the engine stops.
Read the value.
| Result | Proceed to |
| There is no variation in "Engine Speed Cylinder #1 to #4" (All cylinders display approximately the same value for "Engine Speed Cylinder #1 to #4") | A |
| There is variation in "Engine Speed Cylinder #1 to #4" (Only one cylinder displays a value for "Engine Speed Cylinder #1 to #4" that differs considerably) | B |
|
| ||||
| A | ||
| ||
| 6.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure. If the compression pressure of a cylinder is low, inspect the engine assembly and repair or replace parts as necessary .
| NEXT | ||
| ||