DTC P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery |
DTC P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open |
DTC P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent |
DTC P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery |
DTC P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open |
DTC P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent |
DTC P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled |

| DTC No. | DTC Detection Condition | Trouble Area |
| P212012 | VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic). |
|
| P212014 | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P21201F | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P212512 | Both of the following conditions are met for 2 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
|
| P212514 | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P21251F | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P21382B | Difference between VPA and VPA2 is 0.02 V or less for 2 seconds or more (1 trip detection logic). |
|
| Trouble Area | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed | ||
| Accelerator Position Sensor No.1 Voltage | Accelerator Position Sensor No.2 Voltage | Accelerator Position Sensor No.1 Voltage | Accelerator Position Sensor No.2 Voltage | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.75 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Required Sensors/Components | Accelerator pedal sensor assembly |
| Frequency of Operation | Continuous |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR VOLTAGE) |
![]() |
Connect the GTS to the DLC3.
| *a | Fully Depressed |
| *b | Fully Released |
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage.
Read the value displayed on the GTS.
| Accelerator Pedal Operation | Accelerator Position Sensor No.1 Voltage | Accelerator Position Sensor No.2 Voltage | Difference between Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage |
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V | Higher than 0.02 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM) |
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-6 (VPA) - A84-47 (VPA) | Always | Below 1 Ω |
| A36-5 (EPA) - A84-48 (EPA) | Always | Below 1 Ω |
| A36-4 (VCPA) - A84-49 (VCPA) | Always | Below 1 Ω |
| A36-3 (VPA2) - A84-50 (VPA2) | Always | Below 1 Ω |
| A36-2 (EPA2) - A84-51 (EPA2) | Always | Below 1 Ω |
| A36-1 (VCP2) - A84-52 (VCP2) | Always | Below 1 Ω |
| A36-6 (VPA) or A84-47 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A36-4 (VCPA) or A84-49 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A36-3 (VPA2) or A84-50 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| A36-1 (VCP2) or A84-52 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY) |
![]() |
Disconnect the accelerator pedal sensor assembly connector.
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor Assembly) |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-4 (VCPA) - A36-5 (EPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| A36-1 (VCP2) - A36-2 (EPA2) | Engine switch on (IG) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P212012, P212014, P21201F, P212512, P212514, P21251F and/or P21382B are output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||