Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the engine switch is turned on (IG), battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM


A344918E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

1.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY VOLTAGE)
  1. Disconnect the No. 1 integration relay connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    1C-8 - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 7
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the No. 1 integration relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    1D-3 - Body ground
    Always
    11 to 14 V
    1B-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN AND IG2 RELAY)
  1. Inspect the No. 1 integration relay (EFI MAIN and IG2 relay) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1E-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Disconnect the No. 1 integration relay connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1C-1 - A84-6 (IGSW)
    Always
    Below 1 Ω
    1C-9 - A84-2 (+B)
    Always
    Below 1 Ω
    1C-10 - A84-3 (+B2)
    Always
    Below 1 Ω
    1C-7 - A84-46 (MREL)
    Always
    Below 1 Ω
    1C-1 or A84-6 (IGSW) - Body ground and other terminals
    Always
    10 kΩ or higher
    1C-9 or A84-2 (+B) - Body ground and other terminals
    Always
    10 kΩ or higher
    1C-10 or A84-3 (+B2) - Body ground and other terminals
    Always
    10 kΩ or higher
    1C-7 or A84-46 (MREL) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E96-53 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY)
  1. Disconnect the No. 1 integration relay connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A43-9 (IG2D) - 1C-8
    Always
    Below 1 Ω
    A43-9 (IG2D) or 1C-8 - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART ENTRY AND START SYSTEM (Click here)