Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

WIRING DIAGRAM


A340665E03


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following procedure.
  2. After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if the engine can be cranked.

    Result:

    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked
    B



B
Go to step 12
A


2.READ VALUE USING GTS (STARTER SW)
  1. Connect the GTS to DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

  1. Check the value displayed on the GTS when the engine switch is turned to on (IG) and on (Start) positions.

    OK:

    Engine Switch Position
    Starter SW
    On (IG)
    OFF
    On (Start)
    ON



NG
Go to step 9
OK


3.INSPECT RELAY (ST RELAY)
  1. Inspect the ST relay .



NG
REPLACE RELAY (ST RELAY)
OK


4.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here).



NG
REPLACE STARTER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (ST relay) - E9-1
    Always
    Below 1 Ω
    3 (ST relay) or E9-1 - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
  1. Disconnect the starter assembly connector.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Positive (+) battery terminal - F2-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1 (ST relay) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E85-9 (L) - 2 (ST relay)
    Always
    Below 1 Ω
    A84-29 (STA) - 2 (ST relay)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY) 

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A43-5 (STAR) - E85-4 (B)
    Always
    Below 1 Ω
    A43-5 (STAR) - A84-57 (NSW)
    Always
    Below 1 Ω
    A43-5 (STAR), E85-4 (B) or A84-57 (NSW) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2 (ST relay) - E85-9 (L)
    Always
    Below 1 Ω
    2 (ST relay), E85-9 (L), A84-29 (STA) or A43-7 (STA) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART ENTRY AND START SYSTEM (Click here)  

12.READ VALUE USING GTS (STARTER SW)
  1. Connect the GTS to DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

  1. Check the value displayed on the GTS when the engine switch is turned to on (IG) and on (Start) positions.

    OK:

    Engine Switch Position
    Starter SW
    On (IG)
    OFF
    On (Start)
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)