Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:
It is not necessary to remove the stiffening crankcase ring pin unless it is being replaced.



    A336699E01
  1. Using a plastic hammer, tap in 2 new stiffening crankcase ring pins until they stop.
    Text in Illustration 
    *a
    Protrusion Height

    Standard Protrusion Height:
    4.3 to 5.3 mm (0.169 to 0.209 in.)



2. INSTALL STIFFENING CRANKCASE STUD BOLT

NOTICE:
If a stiffening crankcase stud bolt is deformed or its threads are damaged, replace it.



    A302211E02
  1. Stiffening crankcase assembly front side:
    Text in Illustration 
    *a
    Adhesive

    1. When reusing the stiffening crankcase stud bolts:
      Apply adhesive 1324 to the threaded portion (stiffening crankcase assembly side) of the stud bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      NOTICE:
      Install the stud bolt within 3 minutes of applying adhesive.



  1. Using E5 and E8 "TORX" socket wrenches, install the stiffening crankcase stud bolts.


    A336698E01


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *a
    Front Side
    *b
    Lower Side
    *c
    20 mm (0.787 in.)
    *d
    13 mm (0.512 in.)
    *e
    35 mm (1.38 in.)
    *f
    8.5 mm (0.335 in.)
    *g
    8.0 mm (0.315 in.)
    *h
    18 mm (0.709 in.)

    Torque:
    Stud Bolt (A):
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

    Torque:
    Stud Bolt (B):
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL OIL FILTER BRACKET CLIP


    A337610
  1. Install the oil filter bracket clip to the stiffening crankcase assembly.



4. INSTALL ENGINE BALANCER ASSEMBLY


    A198170E04
  1. Check that the alignment marks of the balance shaft damper cover and No. 1 balance shaft driven gear are aligned.
    Text in Illustration 
    *a
    Alignment Mark
    If the alignment marks are not aligned, align them.



      A198171E08
    1. Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the No. 2 balance shaft in place.
      Text in Illustration 
      *a
      No. 1 Balance Shaft Driven Gear
      *b
      Balance Shaft Damper Cover
      *c
      Alignment Mark

    2. Rotate the balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the No. 1 balance shaft driven gear with the alignment mark of the balance shaft damper cover.



    A338405E01
  1. Install the engine balancer assembly to the stiffening crankcase assembly with the 3 bolts, and tighten the bolts in the order shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



5. INSTALL STIFFENING CRANKCASE ASSEMBLY


    A339207E01
  1. Rotate the crankshaft clockwise so that the crankshaft pulley key is at the position 90° from the bottom as shown in the illustration.
    Text in Illustration 
    *1
    Crankshaft Pulley Key



    A258254E02
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    V100145
    Stiffening Crankcase Assembly
    V100146
    Cylinder Block Sub-assembly
    *a
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    *b
    7.0 to 9.0 mm (0.276 to 0.354 in.)

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Dimension:
    Area
    Specified Condition
    Continuous Line
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    Dashed Line
    7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick

    Application Length (A):
    28 mm (1.10 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    3. Do not apply oil for at least 2 hours after the installation.



    A285537E01
  1. Check that the rear cutouts are as shown in the illustration.
    Text in Illustration 
    *a
    Cutout

  1. Clean the bolts and the bolt holes.



    A198186E04
  1. Apply adhesive to 3 or more threads at the tip of the bolts (A).
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A337930E01
  1. Temporarily install the stiffening crankcase assembly with the 11 bolts.
    Text in Illustration 
    *a
    Bolt Type
    *b
    Tightening Order

    Bolt Length:
    Item
    Length
    Bolt (A)
    65 mm (2.56 in.)
    Bolt (B)
    35 mm (1.38 in.)
    Bolt (C)
    125 mm (4.92 in.)
    Bolt (D)
    165 mm (6.50 in.)

    HINT:
    Apply adhesive to the bolts (A) before installation.

  1. Tighten the 11 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

    Torque:
    Bolt (A):
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Torque:
    except Bolt (A):
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



6. INSTALL NO. 1 OIL PAN BAFFLE PLATE


    A337925E01
  1. Install the No. 1 oil pan baffle plate and uniformly tighten the 4 bolts in several steps, in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the clamp to the No. 1 oil pan baffle plate.



7. INSTALL OIL LEVEL SENSOR BRACKET


    A337924
  1. Install the oil level sensor bracket to the stiffening crankcase assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. INSTALL ENGINE OIL LEVEL SENSOR
  1. Install the engine oil level sensor with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the clamp.

  1. Install a new clip to the engine oil level sensor.

  1. Connect the engine oil level sensor connector.



9. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Apply a light coat of engine oil to a new gasket.



    A337923E01
  1. Align the protrusion of the gasket with the cutout of the oil strainer sub-assembly, and install the gasket to the oil strainer sub-assembly.
    Text in Illustration 
    *a
    Protrusion

  1. Install the oil strainer sub-assembly with the 3 bolts in several steps, in the order shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



10. INSTALL OIL PAN SUB-ASSEMBLY


    A210205E02
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Packing Diameter:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    A337281E03
  1. Install the oil pan sub-assembly with the 11 bolts and 2 nuts in several steps, in the order shown in the illustration.
    Text in Illustration 
    *A
    Type A
    *B
    Type B
    V100135
    Bolt
    V100136
    Nut

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    The bolt (A) and nut (A) are tightened twice.



11. INSTALL OIL PAN DRAIN PLUG
  1. Install a new gasket and the oil pan drain plug to the oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



12. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.



    A337618E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise engine oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element in the oil filter cap assembly.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and install the oil filter cap assembly.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A281504E02
  1. Using SST, tighten the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Oil Filter Bracket
    *a
    No Gap

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
    2. Do not cross thread the oil filter cap assembly.



    A194918E04
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Remove any dirt or foreign matter from the installation surface.

  1. Install the oil filter drain plug to the oil filter cap assembly.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



13. INSTALL REAR ENGINE OIL SEAL
  1. Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

    NOTICE:
    1. Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.
    2. To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.
    3. Using an engine sling device and engine lift, secure the engine assembly before service.

  1. Remove any old seal packing.



    A342966E01
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    3.0 mm (0.118 in.)

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install a new rear engine oil seal within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. Apply MP grease to the lip of a new rear engine oil seal.

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not allow MP grease to contact the dust seal.



    A337176E01
  1. Using SST and a hammer, tap in the rear engine oil seal.
    Text in Illustration 
    *a
    Standard Depth (from edge of cylinder block sub-assembly)

    SST
    09223-15030  
    09950-70010   (09951-07150)

    Standard Depth:
    -0.2 to 0.9 mm (-0.00787 to 0.0354 in.)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap in the rear engine oil seal at an angle.



14. INSTALL CYLINDER BLOCK WATER JACKET SPACER


    A336700
  1. Install the cylinder block water jacket spacer to the cylinder block sub-assembly.



15. INSTALL CYLINDER HEAD GASKET
  1. Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.



    A348181E01
  1. Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *1
    Cylinder Head Gasket
    *a
    Lot No.
    *b
    3.0 to 5.0 mm (0.118 to 0.197 in.)
    *c
    152.5 mm (6.00 in.)
    *d
    38 mm (1.50 in.)
    *e
    7.0 to 9.0 mm (0.276 to 0.354 in.)
    *f
    5.0 to 7.0 mm (0.197 to 0.276 in.)
    V100135
    Front
    V100136
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

  1. Place the cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

    NOTICE:
    Pay attention to the installation direction.



16. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head set bolts are tightened in 4 progressive steps.

  1. Place the cylinder head sub-assembly on the cylinder block sub-assembly.

    NOTICE:
    1. Ensure that no oil is on the contact surface of the cylinder head sub-assembly.
    2. Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.

  1. Install the 10 plate washers to the 10 cylinder head set bolts.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.



  1. Step 1:



      A337611E02
    1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head set bolts in several steps, in the order shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

      NOTICE:
      Do not drop the plate washers for the cylinder head set bolts into the cylinder head sub-assembly.

  1. Step 2:

    1. Check that the cylinder head set bolts are tightened to the specified torque.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }



  1. Step 3:



      A307124E04
    1. Mark each cylinder head set bolt head with paint as shown in the illustration.
      Text in Illustration 
      *a
      Paint Mark
      V100135
      Front

    2. Tighten the cylinder head set bolts by 90° in the order shown in step 1.

  1. Step 4:

    1. Tighten the cylinder head set bolts by another 90° in the order shown in step 1.

    2. Check that the paint marks are now facing rearward.

      NOTICE:
      1. Do not apply oil for at least 2 hours after installation.
      2. Do not start the engine for at least 2 hours after installation.
      3. After installation, if the seal packing has seeped out, wipe it off.

      HINT:
      Perform "Inspection After Repair" after replacing the cylinder head sub-assembly (Click here).



17. INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
It is not necessary to remove the camshaft bearing cap setting ring pin unless it is being replaced.



    A336701E01
  1. Using a plastic hammer, tap in 8 new camshaft bearing cap setting ring pins to the camshaft housing sub-assembly.
    Text in Illustration 
    *a
    Protrusion Height

    Standard Protrusion Height:
    2.7 to 3.3 mm (0.106 to 0.130 in.)



18. INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:
It is not necessary to remove the camshaft housing straight pin unless it is being replaced.



    A336702E01
  1. Using a plastic hammer, tap in 2 new camshaft housing straight pins to the camshaft housing sub-assembly.
    Text in Illustration 
    *a
    Protrusion Height

    Standard Protrusion Height:
    5.0 to 7.0 mm (0.197 to 0.276 in.)



19. INSTALL CAMSHAFT HOUSING STUD BOLT

NOTICE:
If a camshaft housing stud bolt is deformed or its threads are damaged, replace it.



    A302211E02
  1. When reusing the camshaft housing stud bolts:
    Text in Illustration 
    *a
    Adhesive

    1. Apply adhesive 1324 to the threaded portion (camshaft housing sub-assembly side) of the stud bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      NOTICE:
      Install the camshaft housing stud bolt within 3 minutes of applying adhesive.



    A336703E01
  1. Using an E8 "TORX" socket wrench, install the camshaft housing stud bolt.
    Text in Illustration 
    *a
    20 mm (0.787 in.)
    *b
    13 mm (0.512 in.)
    *c
    35 mm (1.38 in.)

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



20. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem cap ends.

  1. Install the 16 valve stem caps to the cylinder head sub-assembly.

    NOTICE:
    Do not drop the valve stem caps into the cylinder head sub-assembly.



21. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect the 16 valve lash adjuster assemblies before installing them .

  1. Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

    NOTICE:
    Install each valve lash adjuster assembly to the same place it was removed from.



22. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    A337584E01
  1. Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap

  1. Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.



23. INSTALL NO. 1 CAMSHAFT BEARING


    A337931E01
  1. Clean the No. 1 camshaft bearing.
    Text in Illustration 
    *a
    Vernier Caliper

  1. Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.

  1. Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

    Difference Between (A) and (B):
    0 to 0.7 mm (0 to 0.0276 in.)



24. INSTALL NO. 2 CAMSHAFT BEARING
  1. Clean the No. 2 camshaft bearing.

  1. Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.



    A198177E06
  1. Using a vernier caliper, measure the distance between the camshaft housing sub-assembly edge and the No. 2 camshaft bearing edge.
    Text in Illustration 
    *a
    Vernier Caliper

    Standard Distance:
    1.15 to 1.85 mm (0.0453 to 0.0728 in.)



25. INSTALL OIL CONTROL VALVE FILTER


    A337607
  1. Install the oil control valve filter to the No. 1 camshaft bearing cap.



26. INSTALL CAMSHAFT
  1. Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

  1. Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.

  1. Install the camshaft to the camshaft housing sub-assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft (Click here).



27. INSTALL NO. 2 CAMSHAFT
  1. Clean the camshaft journals and camshaft housing sub-assembly.

  1. Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.

  1. Install the No. 2 camshaft to the camshaft housing sub-assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the No. 2 camshaft (Click here).



28. INSTALL CAMSHAFT BEARING CAP
  1. Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap in their correct positions.



    A337605E02
  1. Install the 11 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    NOTICE:
    Make sure that the camshaft and No. 2 camshaft rotate smoothly after installing the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.



29. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY


    A337584E01
  1. Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap



    A337899E01
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing
    *b
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    *c
    3.5 to 4.0 mm (0.138 to 0.157 in.)

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.



    A337900E01
  1. Position the knock pins of the camshaft and No. 2 camshaft as shown in the illustration.
    Text in Illustration 
    *a
    Approximately 17°
    *b
    Approximately 2°
    *c
    Knock Pin



    A337603E02
  1. Install the camshaft housing sub-assembly, and then install the 20 bolts in the order shown in the illustration.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    NOTICE:
    1. Do not apply oil for at least 2 hours after installation.
    2. Do not start the engine for at least 2 hours after installation.
    3. After installation, if the seal packing has seeped out, wipe it off.



30. INSTALL OIL PIPE SUB-ASSEMBLY


    A337599
  1. Install the oil pipe sub-assembly to the No. 4 camshaft bearing cap with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



31. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    A337582E01
  1. Align and fit the knock pin of the No. 2 camshaft with the knock pin hole of the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Knock Pin Hole
    *b
    Knock Pin

    NOTICE:
    Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the knock pin of the No. 2 camshaft.



    A328700E01
  1. Check that there is no gap between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Exhaust Gear Assembly
    *a
    Incorrect
    *b
    Correct
    *c
    No. 2 Camshaft Flange
    *d
    Gap
    *e
    No Gap



    A337598E01
  1. Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing exhaust gear assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (Click here).



32. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY


A378076E01

NOTICE:
There are different types of camshaft timing gear bolts. Make sure to check the identification mark to determine the tightening torque.
Identification Mark 
Item
Identification Mark Stamp
Type A
A
Type B
D

Text in Illustration 
*a
Identification Mark Stamp


    A337613E01
  1. Align and fit the knock pin of the camshaft with the knock pin hole of the camshaft timing gear assembly.
    Text in Illustration 
    *a
    Knock Pin Hole
    *b
    Knock Pin

    NOTICE:
    Be careful not to damage the contact surface of the camshaft timing gear assembly with the knock pin of the camshaft.



    A328695E01
  1. Check that there is no gap between the camshaft timing gear assembly and portion (A) of the camshaft shown in the illustration.
    Text in Illustration 
    *1
    Camshaft Timing Gear Assembly
    *a
    Incorrect
    *b
    Correct
    *c
    Portion (A) of Camshaft
    *d
    Gap
    *e
    No Gap



    A337898
  1. Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.

  1. Temporarily install the camshaft timing gear bolt.

    HINT:
    Make sure that the camshaft timing gear bolt is screwed in by at least 3 threads.



    A337596E01
  1. Using a wrench to hold the hexagonal portion of the camshaft, tighten the camshaft timing gear bolt.
    Text in Illustration 
    *a
    Hold
    V100135
    Turn

    Torque:
    Type A:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }
    Type B:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
    2. Do not disassemble the camshaft timing gear assembly.

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).



33. INSTALL CRANKSHAFT TIMING SPROCKET


    A337609
  1. Install the crankshaft timing sprocket to the crankshaft.



34. ADD ENGINE OIL


    A337902
  1. Add 50 cc (3.1 cu. in.) of engine oil into the oil hole shown in the illustration.

    NOTICE:
    1. Engine oil must be added if the valve lash adjuster assemblies were removed.
    2. Make sure that the low pressure chamber and oil paths of the valve lash adjuster assemblies are full of engine oil.



35. INSTALL NO. 1 CHAIN VIBRATION DAMPER


    A337594
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



36. INSTALL CHAIN SUB-ASSEMBLY


    A339208E01
  1. Temporarily install the crankshaft pulley set bolt.

  1. Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.



    A337904E01
  1. Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.
    Text in Illustration 
    *a
    Approximately 7°
    *b
    Approximately 32°
    *c
    Timing Mark

    HINT:
    "A" is not a timing mark.

  1. Place the chain sub-assembly onto the camshaft timing exhaust gear assembly, camshaft timing gear assembly and crankshaft timing sprocket.

    HINT:
    1. Make sure the mark plate of the chain sub-assembly faces away from the engine.
    2. It is not necessary to install the chain sub-assembly to the teeth of the gears and sprocket.



    A337905E01
  1. Align the mark plate (orange) of the chain sub-assembly with the timing mark of the camshaft timing exhaust gear assembly and install the chain sub-assembly to the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Mark Plate
    *b
    Timing Mark



    A339209E01
  1. Align the mark plate (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.
    Text in Illustration 
    *a
    Mark Plate
    *b
    Timing Mark



    A339210
  1. Tie a string above the crankshaft timing sprocket so that the chain sub-assembly is secure.



    A337906E01
  1. Using a wrench, hold the hexagonal portion of the camshaft and rotate the camshaft counterclockwise to align the timing mark of the camshaft timing gear assembly with the mark plate (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing gear assembly.
    Text in Illustration 
    *a
    Mark Plate
    *b
    Timing Mark

    HINT:
    Hold the camshaft in place with a wrench until the No. 1 chain tensioner assembly is installed.



    A337907
  1. Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain sub-assembly so that the chain tensioner slipper can be installed.

    NOTICE:
    Make sure the chain sub-assembly is secure.



37. INSTALL CHAIN TENSIONER SLIPPER


    A337593
  1. Install the chain tensioner slipper with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



38. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    A337602
  1. Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Remove the pin from the stopper plate.



39. INSTALL TIMING CHAIN GUIDE


    A337592
  1. Install the timing chain guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



40. SET NO. 1 CYLINDER TO TDC/COMPRESSION


  1. Temporarily install the crankshaft pulley set bolt.


    A337591E01


    Text in Illustration 
    *1
    Crankshaft Pulley Key
    -
    -
    *a
    Approximately 7°
    *b
    Approximately 32°
    *c
    Timing Mark
    -
    -

  1. Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.

  1. Check that the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are as shown in the illustration.

    HINT:
    "A" is not a timing mark.



41. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    A337955E01
  1. Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.
    Text in Illustration 
    *1
    Oil Pump Gasket
    *2
    Oil Hole Cover Gasket

  1. Install the 2 oil pump gaskets and oil hole cover gasket to the stiffening crankcase assembly.



    A337953E01
  1. Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft Timing Sprocket



  1. Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.


    A337282E01


    Text in Illustration 
    *a
    3.0 mm or more
    *b
    7.0 mm or more
    *c
    13 mm or more
    -
    -

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


    Seal Packing Application Chart:

    Area
    Seal Packing Diameter (Round)
    Distance from Edge of Cover to Center of Seal Packing
    Seal Packing Application Length
    Seal Packing Dimension (Flat)
    Dashed Line
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    A - A
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    2.5 mm (0.0984 in.)
    -
    -
    B - B
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    28 mm (1.10 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    C - C
    7.0 mm (0.276 in.)
    5.0 mm (0.197 in.)
    25 mm (0.984 in.)
    13 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker
    D - D
    5.0 mm (0.197 in.)
    3.0 mm (0.118 in.)
    26 mm (1.02 in.)
    7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
    E
    2.5 to 3.5 mm (0.0984 to 0.138 in.)
    3.0 mm (0.118 in.)
    -
    -

    NOTICE:
    1. Clean the surfaces with non-residue solvent before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
    3. After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
    4. Do not add oil for at least 2 hours after installation.
    5. Do not start the engine for at least 2 hours after installation.



  1. Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.


    A337954E03


    Text in Illustration 
    *a
    Torque
    *b
    Tightening Order
    V100135
    Bolt
    V100136
    Nut

    Bolt Length:

    Item
    Length
    Thread Diameter
    Bolt (A)
    30 mm (1.18 in.)
    8.0 mm (0.315 in.)
    Bolt (B)
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt (C)
    45 mm (1.77 in.)
    8.0 mm (0.315 in.)

    NOTICE:
    Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.

  1. Tighten the 17 bolts and 2 nuts in several steps, in the order shown in the illustration.

    Torque:
    Bolt (A), (C) and Nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Bolt (B):
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



42. INSTALL ENGINE MOUNTING BRACKET RH


    A337952E01
  1. Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.

    Torque:
    Bolt (1), (2) and (3):
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    Bolt (4) and (5):
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.



43. INSTALL TIMING CHAIN COVER PLATE
  1. Install a new gasket and the timing chain cover plate with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



44. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY


    A332562E01
  1. Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly as shown in the illustration.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Do not damage the O-ring.



    A192239E21
  1. Apply adhesive to 2 or 3 threads of 2 new bolts.
    Text in Illustration 
    *a
    Adhesive 1324

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the camshaft timing oil control solenoid assembly to the timing chain cover sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the camshaft timing oil control solenoid assembly has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control solenoid assembly.

  1. Connect the camshaft timing oil control solenoid assembly connector.



45. INSTALL TIMING CHAIN COVER OIL SEAL
  1. Apply MP grease to the lip of a new timing chain cover oil seal.

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not allow MP grease to contact the dust seal.



    A338522E01
  1. Using SST and a hammer, tap in the timing chain cover oil seal.
    Text in Illustration 
    *a
    Standard Depth (from edge of the timing chain cover sub-assembly)

    SST
    09636-20010  

    Standard Depth:
    -0.75 to -1.45 mm (-0.0295 to -0.0571 in.)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap in the timing chain cover oil seal at an angle.



46. INSTALL CASE SEPARATOR


    A337914E01
  1. Apply a light coat of engine oil to a new O-ring.
    Text in Illustration 
    *a
    O-ring

  1. Install the O-ring to the case separator.

    NOTICE:
    Make sure to securely fit the O-ring into the groove of the case separator.



    A337901
  1. Apply a light coat of engine oil to a new oil separator gasket.

  1. Install the oil separator gasket to the case separator.

    NOTICE:
    Make sure to securely fit the oil separator gasket into the groove of the case separator.



    A337913
  1. Install the case separator to the cylinder head cover case sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



47. INSTALL SPARK PLUG TUBE GASKET


    A337919E01
  1. Tap in 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.
    Text in Illustration 
    *1
    Spark Plug Tube Gasket
    *2
    Cylinder Head Cover Sub-assembly
    *a
    1.0 mm (0.394 in.) or less

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the spark plug tube gasket.
    2. Do not tap in the spark plug tube gasket at an angle.



48. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    A337920E01
  1. Apply a light coat of engine oil to a new camshaft bearing cap oil hole gasket and a new gasket.
    Text in Illustration 
    *1
    Camshaft Bearing Cap Oil Hole Gasket
    *a
    Gasket

  1. Install the camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.

  1. Install the gasket to the No. 2 camshaft bearing cap.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

    NOTICE:
    Remove any oil from the contact surface.



    A337933E01
  1. Apply seal packing as shown in the illustration.
    Text in Illustration 
    *1
    Timing Chain Cover Sub-assembly
    *2
    Camshaft Housing Sub-assembly
    *a
    45 mm (1.77 in.)
    *b
    24 mm (0.945 in.)
    *c
    Seal Packing Diameter: 3.0 mm (0.118 in.)
    *d
    Application Width 5.0 mm (0.197 in.)
    *e
    Seal Packing Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.)
    V100135
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.



    A337903E01
  1. Align the cylinder head cover sub-assembly with the pin (A). Then align the cylinder head cover sub-assembly with the pin (B) and install the cylinder head cover sub-assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Bolt with Seal Washer

  1. Install 3 new seal washers and the 17 bolts, and then tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after installation.



49. INSTALL CRANKSHAFT PULLEY


    A305738E01
  1. Align the crankshaft pulley key with the key groove of the crankshaft pulley.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using SST, hold the crankshaft pulley and install the crankshaft pulley set bolt.

    SST
    09213-54015  
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }

    HINT:
    Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)



50. INSTALL CRANKSHAFT POSITION SENSOR
  1. Clean and degrease the threads of the bolt for the crankshaft position sensor.

  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

    NOTICE:
    If reusing the crankshaft position sensor, be sure to inspect the O-ring.



    A192239E21
  1. Apply adhesive to 2 or 3 threads of the bolt.
    Text in Illustration 
    *a
    Adhesive 1324

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the crankshaft position sensor to the timing chain cover sub-assembly with the bolt.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    NOTICE:
    1. If the crankshaft position sensor has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.

  1. Connect the crankshaft position sensor connector.



51. INSTALL NO. 1 VENTILATION CASE


    A337934E01
  1. Apply seal packing in a continuous line as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard Seal Packing Diameter:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 1 ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.



    A337911E01
  1. Install the No. 1 ventilation case, and install the 8 bolts and 2 nuts in the order shown in the illustration.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    The bolts (A) are tightened twice.



52. INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
  1. Clean and degrease the threads of the PCV valve (ventilation valve sub-assembly).

  1. Apply adhesive to 2 or 3 threads of the PCV valve (ventilation valve sub-assembly).

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 19 mm deep socket wrench, install the PCV valve (ventilation valve sub-assembly) to the cylinder head cover sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



53. INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)
  1. Clean and degrease the threads of the bolt for the camshaft position sensor.

  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    NOTICE:
    If reusing the camshaft position sensor, be sure to inspect the O-ring.



    A192239E21
  1. Apply adhesive to 2 or 3 threads of the bolt.
    Text in Illustration 
    *a
    Adhesive 1324

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the camshaft position sensor has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.

  1. Connect the camshaft position sensor connector.



54. INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)
  1. Clean and degrease the threads of the bolt for the camshaft position sensor.

  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    NOTICE:
    If reusing the camshaft position sensor, be sure to inspect the O-ring.



    A192239E21
  1. Apply adhesive to 2 or 3 threads of the bolt.
    Text in Illustration 
    *a
    Adhesive 1324

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the camshaft position sensor has been struck or dropped, replace it.
    2. Make sure that the O-ring is not cracked or moved out of place when installing the camshaft position sensor.

  1. Connect the camshaft position sensor connector.



55. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.

    NOTICE:
    Do not damage the O-ring.

  1. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. If the camshaft timing oil control valve assembly has been struck or dropped, replace it.
    2. Do not allow foreign matter to contact the oil seal face of the camshaft timing oil control valve assembly (connecting surface with the cylinder head cover subassembly).
    3. Make sure that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.

  1. Connect the camshaft timing oil control valve assembly connector.



56. INSTALL OIL FILLER CAP SUB-ASSEMBLY
  1. Install a new gasket to the oil filler cap sub-assembly.

  1. Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.



57. INSTALL SPARK PLUG

HINT:
Perform "Inspection After Repair" after replacing a spark plug (Click here).

  1. Install the 4 spark plugs to the cylinder head sub-assembly.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    If a spark plug has been struck or dropped, replace it.

    HINT:
    Install the same parts to their original positions.



58. INSTALL ENGINE COVER JOINT


    A338551
  1. Install the 2 engine cover joints.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



59. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).

  1. Install a new gasket to the engine coolant temperature sensor.



    A338021E01
  1. Using SST, install the engine coolant temperature sensor to the cylinder head sub-assembly.

    SST
    09817-33191  

    Torque:
    19.6 N*m{ 20 kgf*cm , 14 ft.*lbf }

    NOTICE:
    If the engine coolant temperature sensor has been struck or dropped, replace it.

  1. Connect the engine coolant temperature sensor connector.



60. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY


    A304094E01
  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge assembly.
    Text in Illustration 
    *a
    Adhesive 1344
    *b
    Oil Inlet Port

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    1. Do not apply adhesive to the oil inlet port of the oil pressure sender gauge assembly.
    2. Install the oil pressure sender gauge assembly within 3 minutes of applying adhesive.

  1. Using a 27 mm deep socket wrench, install the oil pressure sender gauge assembly.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Connect the oil pressure sender gauge assembly connector.



61. INSTALL KNOCK CONTROL SENSOR

HINT:
Perform "Inspection After Repair" after replacing the knock control sensor (Click here).



    A338028E01
  1. Install the knock control sensor to the cylinder block sub-assembly with the bolt so that the knock control sensor installation position is as shown in the illustration.
    Text in Illustration 
    *a
    Top
    *b
    Engine Front
    *c
    7°
    *d
    10°

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    If the knock control sensor has been struck or dropped, replace it.

  1. Connect the knock control sensor connector.



62. INSTALL VACUUM PUMP ASSEMBLY


  1. When installing a new vacuum pump assembly:



      C314619E01
    1. Apply engine oil to the No. 3 O-ring.
      Text in Illustration 
      *1
      No. 2 O-ring
      *2
      No. 3 O-ring
      V100135
      Engine Oil

      NOTICE:
      Do not apply engine oil to the No. 2 O-ring.



  1. When reusing the vacuum pump assembly:



      C314619E01
    1. Install a new No. 2 O-ring to the vacuum pump assembly.
      Text in Illustration 
      *1
      No. 2 O-ring
      *2
      No. 3 O-ring
      V100135
      Engine Oil

    2. Apply engine oil to a new No. 3 O-ring and install it to the vacuum pump assembly.

      NOTICE:
      Do not apply engine oil to the No. 2 O-ring.



    C314608E01
  1. Apply engine oil to the inner surface of the installation hole.
    Text in Illustration 
    *a
    Coupling Teeth
    *b
    Groove
    V100135
    Engine Oil

  1. Align the coupling teeth of the vacuum pump assembly with the groove of the camshaft and install the vacuum pump assembly with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    After tightening the bolts, ensure that the contact surface of the vacuum pump assembly is flush with the cylinder head.