Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the cylinder head sub-assembly (Click here).



1. INSTALL SPARK PLUG TUBE

HINT:
When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.



    A289330E02
  1. Apply adhesive to a new spark plug tube as shown in the illustration.
    Text in Illustration 
    *a
    Adhesive
    *b
    Application Width
    *c
    Distance

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    Standard Application Width:
    1.0 to 3.0 mm (0.0394 to 0.118 in.)

    Distance:
    1.0 to 7.0 mm (0.0394 to 0.276 in.)

    NOTICE:
    1. Install the spark plug tube within 3 minutes of applying adhesive.
    2. Be careful not to deform the spark plug tube.
    3. Do not expose the spark plug tube to engine oil for at least 1 hour after installing it.



    A336672E01
  1. Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

    Standard Protrusion Height:
    112 mm (4.41 in.)

    NOTICE:
    To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

    Text in Illustration 
    *a
    Protrusion Height



2. INSTALL CYLINDER HEAD STUD BOLT


  1. Using an E8 and E10 "TORX" socket wrench, install the 9 cylinder head stud bolts.


    A336673E01


    Text in Illustration 
    *a
    Intake Manifold Side
    *b
    Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) Side
    *c
    Rear Side
    *d
    26 mm (1.02 in.)
    *e
    16.7 mm (0.657 in.)
    *f
    51.7 mm (2.04 in.)
    *g
    14 mm (0.551 in.)
    *h
    13 mm (0.512 in.)
    *i
    29 mm (1.14 in.)
    -
    -

    Torque:
    Stud Bolt (A), (C):
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
    Stud Bolt (B):
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



3. INSTALL NO. 1 STRAIGHT SCREW PLUG


    A337937
  1. Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



4. INSTALL NO. 2 STRAIGHT SCREW PLUG


    A194961
  1. Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }



5. INSTALL VALVE SPRING SEAT
  1. Install the valve spring seats to the cylinder head sub-assembly.



6. INSTALL VALVE STEM OIL SEAL


    A329098E01
  1. Apply a light coat of engine oil to new valve stem oil seals.
    Text in Illustration 
    *a
    Intake Valve Stem Oil Seal
    *b
    Exhaust Valve Stem Oil Seal
    *c
    Brown
    *d
    Gray
    *e
    "NOK" Mark

    NOTICE:
    Pay attention when installing the valve stem oil seals. For example, installing an intake valve stem oil seal onto the exhaust side or installing an exhaust valve stem oil seal onto the intake side can cause installation problems later.

    HINT:
    The intake valve stem oil seals are brown and the exhaust valve stem oil seals are gray.



    A337946E01
  1. Using SST, push in the valve stem oil seals.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the valve stem oil seal to be damaged or improperly seated.



7. INSTALL INTAKE VALVE


    A285332E01
  1. Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the intake valve, compression spring and valve spring retainer to the cylinder head sub-assembly.

    NOTICE:
    Install the same parts in the same combination to their original locations.



    A337935E01
  1. Using SST, compress the compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020  
    09202-00020  



    A339211
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve spring retainer.



8. INSTALL EXHAUST VALVE


    A285332E01
  1. Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the exhaust valve, compression spring and valve spring retainer to the cylinder head sub-assembly.

    NOTICE:
    Install the same parts in the same combination to their original locations.



    A337936E01
  1. Using SST, compress the compression spring and install the 2 valve spring retainer locks.

    SST
    09202-70020  
    09202-00020  



    A339212
  1. Using a plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve spring retainer.