Home › Engine / Hybrid System ยท 6AR-FSE › ENGINE MECHANICAL › CYLINDER BLOCK

CYLINDER BLOCK > REASSEMBLY

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the piston or piston ring set (Click here).



1. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.



  1. Using E8 and E10 "TORX" socket wrenches, install the stud bolts.


    A336690E01


    Text in Illustration 
    *a
    RH Side
    *b
    LH Side
    *c
    20 mm (0.787 in.)
    *d
    13 mm (0.512 in.)
    *e
    35 mm (1.38 in.)
    *f
    46 mm (1.81 in.)
    *g
    19 mm (0.748 in.)
    *h
    67 mm (2.64 in.)

    Torque:
    Stud Bolt (A):
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
    Stud Bolt (B):
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



2. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY


    A337948
  1. Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL PISTON
  1. Using a screwdriver, install a new piston pin hole snap ring (rear side) at one end of the piston pin hole.

    HINT:
    1. Perform this procedure only when replacement of the piston pin hole snap ring (rear side) is necessary.
    2. Tape the screwdriver tip before use.

  1. Gradually heat the piston to 80 to 90°C (176 to 194°F).

  1. Coat the piston, piston pin and connecting rod with engine oil.



    A336691E01
  1. Align the cutout of the piston and front mark of the connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the piston pin hole snap ring.
    Text in Illustration 
    *a
    Cutout
    *b
    Front Mark

    NOTICE:
    Do not change the combination of the pistons and piston pins.



    A336692E04
  1. Using a screwdriver, install a new piston pin hole snap ring (front side) on the other side of the piston pin hole.
    Text in Illustration 
    *1
    Piston Pin Hole Snap Ring
    *a
    Cutout
    *b
    Protective Tape

    HINT:
    1. Be sure that the end gap of the piston pin hole snap ring is not aligned with the service hole front mark portion of the piston.
    2. Tape the screwdriver tip before use.



    A336693
  1. Check the fitting condition between the piston and piston pin.

    1. Move the connecting rod back and forth on the piston pin. Check the fitting condition. If abnormal movement is felt, replace the piston and piston pin as a set.

    2. Rotate the piston back and forth on the piston pin. Check the fitting condition.
      If abnormal movement is felt, replace the piston and piston pin as a set.

      HINT:
      Perform "Inspection After Repair" after replacing the piston (Click here).



4. INSTALL PISTON RING SET


    A336694E01
  1. Install the oil ring expander, upper side rail and lower side rail by hand.
    Text in Illustration 
    *a
    Upper Side Rail
    *b
    Oil Ring Expander
    *c
    Lower Side Rail
    *d
    Groove for Oil Ring Expander, Upper Side Rail and Lower Side Rail

    NOTICE:
    Make sure that the oil ring expander ends do not overlap each other.



    A336695E01
  1. Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.
    Text in Illustration 
    *a
    No. 1 Compression Ring
    *b
    No. 2 Compression Ring
    *c
    Code Mark
    *d
    Paint Mark
    V100135
    Upward

    Piston Ring Mark:
    Item
    Code Mark
    Paint Mark
    No. 1 Compression Ring
    -
    Yellow
    No. 2 Compression Ring
    A2
    Blue

    NOTICE:
    1. The No. 1 compression ring can be installed with either side facing upward.
    2. Install the No. 2 compression ring with the code mark (A2) facing upward.
    3. Paint marks can only be checked on new compression rings. When reusing compression rings, check each compression ring profile in order to install them to the correct positions.

    HINT:
    Perform "Inspection After Repair" after replacing the piston ring set (Click here).



    A336696E01
  1. Position the piston rings so that the ring ends are as shown in the illustration.
    Text in Illustration 
    *a
    No. 1 Compression Ring
    *b
    No. 2 Compression Ring
    *c
    Upper Side Rail
    *d
    Oil Ring Expander
    *e
    Lower Side Rail
    *f
    Front Mark
    V100135
    Front Side



5. INSTALL CRANKSHAFT PULLEY KEY
  1. Install the 2 crankshaft pulley keys to the crankshaft.



6. INSTALL CRANKSHAFT BEARING


    A195816E04
  1. Clean the main journal and both surfaces of the crankshaft bearings and No. 2 crankshaft bearings.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

  1. Install the crankshaft bearings to the cylinder block sub-assembly as shown in the illustration.

    NOTICE:
    1. Do not apply engine oil to the crankshaft bearings and the contact surfaces.
    2. Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.
    3. Do not allow coolant to come into contact with the crankshaft bearing inner surface.
    4. If any coolant comes into contact with the crankshaft bearing inner surface, replace the crankshaft bearing with a new one.



    A195817E06
  1. Install the No. 2 crankshaft bearings onto the crankshaft bearing caps.
    Text in Illustration 
    *a
    Vernier Caliper

  1. Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the No. 2 crankshaft bearing edge.

    Difference Between (A) and (B):
    0 to 0.7 mm (0 to 0.0276 in.)

    NOTICE:
    1. Do not apply engine oil to the No. 2 crankshaft bearings and the contact surfaces.
    2. Do not allow coolant to come into contact with the No. 2 crankshaft bearing inner surface.
    3. If any coolant comes into contact with the No. 2 crankshaft bearing inner surface, replace the No. 2 crankshaft bearing with a new one.



7. INSTALL CRANKSHAFT THRUST WASHER


    A337947E02
  1. Apply engine oil to the crankshaft thrust washers.
    Text in Illustration 
    *a
    Oil Groove

  1. Install the 2 crankshaft thrust washers onto the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.



8. INSTALL CRANKSHAFT


    A338968E01
  1. Apply engine oil to the crankshaft bearings, and place the crankshaft on the cylinder block sub-assembly.
    Text in Illustration 
    *a
    Front Mark

  1. Apply engine oil to the No. 2 crankshaft bearings.

  1. Confirm the front marks and numbers, and install the 5 crankshaft bearing caps onto the cylinder block sub-assembly with the front marks as shown in the illustration.

    HINT:
    The crankshaft bearing cap bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap bolts.



  1. Step 1:



      A338969E03
    1. Uniformly install and tighten the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Step 2:

    1. Tighten the 10 crankshaft bearing cap bolts again in the order shown in the illustration.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }

      If a crankshaft bearing cap bolt cannot be tightened to the specified torque, replace it.



  1. Step 3:



      A132155E08
    1. Mark the front of the crankshaft bearing cap bolts with paint.
      Text in Illustration 
      *a
      Paint Mark
      V100136
      Engine Front

    2. Tighten the crankshaft bearing cap bolts by 90° in the order shown in the illustration.

    3. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.



9. INSTALL CONNECTING ROD BEARING


    A195818E08
  1. Clean the connecting rod bearing contact surface of the connecting rod and connecting rod cap, and both surfaces of both connecting rod bearings.
    Text in Illustration 
    *a
    Vernier Caliper

  1. Install the connecting rod bearings to the connecting rods and connecting rod caps.

  1. Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the edges of the connecting rod cap and connecting rod bearing.

    Difference Between (A) and (B):
    0 to 0.7 mm (0 to 0.0276 in.)

    NOTICE:
    1. Do not apply engine oil to the connecting rod bearings and the contact surfaces.
    2. Do not allow coolant to come into contact with the connecting rod bearing inner surface.
    3. If any coolant comes into contact with the connecting rod bearing inner surface, replace the connecting rod bearing with a new one.



10. INSTALL PISTON WITH CONNECTING ROD


    A336696E01
  1. Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.
    Text in Illustration 
    *a
    No. 1 Compression Ring
    *b
    No. 2 Compression Ring
    *c
    Upper Side Rail
    *d
    Oil Ring Expander
    *e
    Lower Side Rail
    *f
    Front Mark
    V100135
    Front Side

  1. Position the piston rings so that the ring ends are as shown in the illustration.

    HINT:
    Regardless of the front mark, the piston rings are positioned correctly if their ends are positioned opposite of each other.



    A336697E01
  1. Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing the engine front.
    Text in Illustration 
    *a
    Front Mark

    NOTICE:
    When inserting the piston with connecting rod into the cylinder block sub-assembly, make sure the No. 1 oil nozzle sub-assembly does not interfere with the connecting rod.



    A338773E01
  1. Check that the front mark of the connecting rod cap is facing in the correct direction.
    Text in Illustration 
    *a
    Front Mark

    NOTICE:
    Match the connecting rod cap with the connecting rod.



    A338771
  1. Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.

  1. Temporarily install the 2 connecting rod bolts.

    HINT:
    The connecting rod bolts are tightened in 2 progressive steps.

  1. Step 1:

    1. Alternately tighten the 2 connecting rod bolts in several steps.

      Torque:
      40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    A101478E31
  1. Step 2:
    Text in Illustration 
    *a
    Paint Mark
    V100136
    Engine Front

    1. Mark the front of the 2 connecting rod bolts with paint.

    2. Tighten the connecting rod bolts by 90° as shown in the illustration.

    3. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.