FUEL SYSTEM > PRECAUTION |
| 1.BEFORE WORKING ON FUEL SYSTEM |
Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.
Do not smoke or work near fire when handling the fuel system.
Keep fuel away from rubber or leather parts.
| 2.DISCHARGE FUEL SYSTEM PRESSURE |
Remove the rear seat cushion assembly .
Remove the rear seat cushion lock hook .
![]() |
Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.
| *a | Protective Tape |
Disconnect the fuel pump connector.
Start the engine. After the engine has stopped on its own, turn the engine switch off.
Crank the engine again and make sure that the engine does not start.
Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.
Disconnect the cable from the negative (-) battery terminal.
Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.
Clean the installation surfaces of the rear floor service hole cover and vehicle body.
Connect the fuel pump connector.
Install the rear floor service hole cover with new butyl tape.
Install the rear seat cushion lock hook .
Install the rear seat cushion assembly .
| 3.FUEL LINE |
When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:
Discharge fuel system pressure (See step 2).
Disconnect the fuel tube.
Drain the fuel remaining inside the fuel pump tube into a container.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Quick Type A:
Perform the following procedure when disconnecting a fuel tube connector.
![]() |
Clamp Type:
Open the cover and remove the EFI fuel pipe clamp from the fuel tube connector.
![]() |
Cover Type:
Pull off the fuel tube connector cover.
| *a | Fuel Tube Connector Cover |
![]() | Pull off |
Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.
![]() |
Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
| *a | Retainer |
| *b | O-ring |
| *c | Fuel Tube Connector |
| *d | Nylon Tube |
| *e | Fuel Pipe |
![]() | Pinch |
![]() | Pull |
If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.
Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Quick Type A:
Perform the following procedure when connecting a fuel tube connector.
Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.
![]() |
After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
![]() | Pull |
Clamp Type:
Install the EFI fuel pipe clamp to the fuel tube connector and close the cover.
Cover Type:
Push in the fuel tube connector cover.
Inspect for fuel leaks .
Quick Type B:
Perform the following procedure when disconnecting a fuel tube connector.
![]() |
Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.
| *a | Retainer |
| *b | Fuel Pipe |
| *c | Nylon Tube |
| *d | Fuel Tube Connector |
| *e | O-ring |
| *f | Claw |
![]() | Push |
![]() | Pull out |
![]() | Pull off |
If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.
Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Quick Type B:
Perform the following procedure when connecting a fuel tube connector.
![]() |
Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.
| *a | Retainer |
| *b | Claw |
![]() | Push |
![]() | Push in |
Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
Inspect for fuel leaks .
![]() |
Observe the following precautions when handling a nylon tube:
| *a | Fuel Tube Connector |
| *b | Nylon Tube |
| *c | Ethylene Propylene Diene Monomer (EPDM) Rubber Protector |
| 4.PORT FUEL INJECTOR ASSEMBLY |
![]() |
Observe the following precautions when removing and installing the port fuel injector assemblies:
| *1 | O-ring |
| *2 | Fuel Delivery Pipe |
| *a | Correct |
| *b | Incorrect |
Do not reuse the O-ring or injector vibration insulator.
When placing a new O-ring to the port fuel injector assembly, do not damage the O-ring.
Coat a new O-ring with gasoline or spindle oil before installing it.
![]() |
Install the port fuel injector assembly to the fuel delivery pipe and cylinder head sub-assembly as shown in the illustration.
| *1 | Fuel Delivery Pipe |
| *2 | O-ring |
| *3 | Injector Vibration Insulator |
| *4 | Port Fuel Injector Assembly |
| 5.FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
![]() |
| *a | Tube |
| 6.INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs .