Home › Engine / Hybrid System · 6AR-FSE › FUEL › FUEL INJECTOR (for Port Injection)

FUEL INJECTOR (for Port Injection) > INSPECTION

for Preparation Click here



1. INSPECT PORT FUEL INJECTOR ASSEMBLY


  1. Check the resistance.



      A335666E01
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *a
      Component without harness connected
      (Port Fuel Injector Assembly)
      Standard Resistance: 
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      20°C (68°F)
      11.6 to 12.4 Ω
      If the result is not as specified, replace the port fuel injector assembly.



  1. Check the operation.

    CAUTION:
    Perform the inspection in a well-ventilated area. Do not perform the inspection near an open flame.


    1. Remove the EFI fuel pipe clamp (Click here).

    2. Disconnect the fuel tube sub-assembly (Click here).



    3. A264971E08
    4. Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).
      Text in Illustration 
      *a
      SST (Hose)
      *b
      SST (Hose Band)
      *c
      SST (Fuel Tube Connector)
      *d
      Fuel Pipe (Vehicle Side)

      SST
      09268-31014   (09268-41500, 09268-41700, 95336-08070)

      NOTICE:
      Make sure the SST (fuel tube connector) O-rings are not damaged and are free of foreign matter as they are used to seal the connections between the fuel tube connector and fuel pipe.

    5. Apply a light coat of gasoline to a new O-ring, and then install the O-ring to the port fuel injector assembly.



    6. A300546E03
    7. Connect SST (adapter) and SST (hose) to the port fuel injector assembly, and hold the port fuel injector assembly and union with SST (clamp).
      Text in Illustration 
      *1
      O-ring
      *a
      SST (Adapter)
      *b
      SST (Hose Band)
      *c
      SST (Clamp)
      *d
      SST (Hose)
      *e
      Vinyl Tube

      SST
      09268-31014   (09268-41600, 09268-41300, 09268-41700, 95336-08070)



    8. A300548E03
    9. Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.
      Text in Illustration 
      *a
      Lock
      *b
      SST (Tie Band)

      SST
      09268-31014   (09268-41800)

      NOTICE:
      1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
      1. Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.

      HINT:
      When removing SST (tie band), disengage the lock.

    10. Check that SST (clamp) and SST (adapter) cannot be easily separated.

    11. Install a vinyl tube to the port fuel injector assembly.

      CAUTION:
      Install a suitable vinyl tube to the port fuel injector assembly to prevent fuel from spraying.

    12. Set the port fuel injector assembly in a graduated cylinder.

    13. Operate the fuel pump .



    14. A300547E03
    15. Connect SST (EFI inspection wire H) to the port fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each port fuel injector assembly 2 or 3 times.
      Text in Illustration 
      *a
      SST (EFI Inspection Wire H)

      SST
      09842-30080  
      Standard Injection Volume: 
      Tester Connection
      Condition
      Specified Condition
      Positive (+) battery terminal -
      Negative (-) battery terminal
      Per 15 seconds
      54 to 65 cc (3.3 to 4.0 cu. in.)

      Difference between Each Port Fuel Injector Assembly:
      11 cc (0.7 cu. in.) or less

      NOTICE:
      1. Make sure that SST (EFI inspection wire H) is securely connected.
      1. Always switch the voltage on and off at the battery side, not the port fuel injector assembly side.

      If the injection volume is not as specified, replace the port fuel injector assembly.

  1. Check for leaks.

    1. Disconnect SST (EFI inspection wire H) from the battery and check for fuel leaks from the port fuel injector assembly.

      Standard Fuel Drop:
      1 drop or less per 14 minutes

      If the result is not as specified, replace the port fuel injector assembly.

    2. Connect the fuel tube sub-assembly (Click here).

    3. Install the EFI fuel pipe clamp (Click here).

    4. Check for fuel leaks .