Home › Engine / Hybrid System ยท 6AR-FSE › FUEL › FUEL INJECTOR (for Direct Injection)

FUEL INJECTOR (for Direct Injection) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR SEAL


    A273083E03
  1. Apply engine conditioner to the area shown in the illustration. Using a piece of cloth, clean carbon deposits from the direct fuel injector assembly and its grooves.
    Text in Illustration 
    *a
    Area to be Cleaned

    NOTICE:
    1. Do not clean the tip of the direct fuel injector assembly.
    1. Do not use a wire brush to clean the direct fuel injector assembly.
    1. If a direct fuel injector assembly is dropped or the tip of a direct fuel injector assembly is struck, replace it with a new one.



    A273084E04
  1. Apply engine oil to the direct fuel injector assembly contact surface of SST (guide), then attach SST (guide) to the direct fuel injector assembly with the chamfer facing the tip of the direct fuel injector assembly as shown in the illustration.
    Text in Illustration 
    *a
    SST (Guide)
    *b
    Chamfer

    SST
    09260-39021   (09261-03020)



    A273085E03
  1. Install a new fuel injector seal to SST (holder).
    Text in Illustration 
    *1
    Fuel Injector Seal
    *a
    SST (Holder)
    *b
    Correct
    *c
    Incorrect

    SST
    09260-39021   (09261-03011)

    NOTICE:
    Be careful not to install the fuel injector seal to SST (holder) at an angle. Doing so will stretch the fuel injector seal.



    A273086E03
  1. Install SST (holder) with the fuel injector seal to the tip of the direct fuel injector assembly. Slide the fuel injector seal downward into the direct fuel injector assembly groove with your fingers as shown in the illustration.
    Text in Illustration 
    *a
    SST (Holder)
    *b
    SST (Guide)

    SST
    09260-39021   (09261-03011, 09261-03020)

    NOTICE:
    Check that the fuel injector seal is seated in the direct fuel injector assembly groove as shown in the illustration.



    A273087E03
  1. Slowly slide SST (guide) toward the tip of the direct fuel injector assembly. When the direct fuel injector assembly contact surface of SST (guide) aligns with the fuel injector seal as shown in the illustration, hold the position for 5 seconds or more to fully seat the fuel injector seal into the direct fuel injector assembly groove.
    Text in Illustration 
    *a
    SST (Guide)

    SST
    09260-39021   (09261-03020)

    NOTICE:
    Make sure the fuel injector seal is not pinched between SST (guide) and the edge of the direct fuel injector assembly groove. Replace the fuel injector seal if it becomes damaged.

    HINT:
    1. Set SST (guide) so that its bottom surface is flush with the fuel injector seal.
    1. If it is difficult to slide SST (guide) upward, slowly wiggle it from side to side while sliding it up the direct fuel injector assembly little by little.



    A273088E02
  1. After installing the fuel injector seals, check that they are not scratched, deformed or protruding from the direct fuel injector assembly groove.
    Text in Illustration 
    *a
    Normal
    *b
    Protruding
    *c
    Deformed
    *d
    Correct
    *e
    Incorrect

    NOTICE:
    If a fuel injector seal is scratched, deformed or protruding from the groove, replace it with a new one.



2. INSTALL DIRECT FUEL INJECTOR ASSEMBLY

NOTICE:
Perform "Inspection After Repair" after replacing a direct fuel injector assembly (Click here).



    A335645E01
  1. Install a new injector vibration insulator and a new C-ring to the direct fuel injector assembly.
    Text in Illustration 
    *1
    Direct Fuel Injector Assembly
    *2
    C-ring
    *3
    Injector Vibration Insulator
    *a
    Taper

    NOTICE:
    1. Install the taper of the injector vibration insulator by aligning it with the taper of the direct fuel injector assembly.
    1. Check that the C-ring is securely seated in the groove of the direct fuel injector assembly.



  1. Install a new O-ring and a new No. 1 fuel injector back-up ring to the direct fuel injector assembly as shown in the illustration.


    A304564E03


    Text in Illustration 
    *1
    No. 1 Fuel Injector Back-up Ring
    *2
    O-ring
    *a
    No. 1 Fuel Injector Back-up Ring
    Opening
    *b
    Overlapped
    *c
    Stretched
    *d
    Correct
    *e
    Incorrect
    -
    -

    NOTICE:
    1. Check that there is no foreign matter or damage on the O-ring groove of the direct fuel injector assembly.
    1. Make sure that the No. 1 fuel injector back-up ring is installed in the correct orientation.
    1. Make sure that the No. 1 fuel injector back-up ring and O-ring are installed in the correct order.
    1. Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.
    1. After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.



    A273121E02
  1. With the notch of a new No. 3 fuel injector back-up ring facing downward, install the direct fuel injector assembly to the No. 3 fuel injector back-up ring as shown in the illustration.
    Text in Illustration 
    *1
    Direct Fuel Injector Assembly
    *2
    No. 3 Fuel Injector Back-up Ring
    *a
    Notch

    NOTICE:
    1. Make sure that the No. 3 fuel injector back-up ring is installed in the correct orientation.
    1. After installing the No. 3 fuel injector back-up ring, make sure there is no damage or foreign matter.

  1. Install the nozzle holder clamp to each direct fuel injector assembly.



    A273091E02
  1. Align the protrusion of the nozzle holder clamp with the positioning hole of the fuel delivery pipe sub-assembly and insert the direct direct fuel injector assembly.
    Text in Illustration 
    *a
    Protrusion
    *b
    Positioning Hole
    V100135
    No Gap

    NOTICE:
    1. Make sure that there is no foreign matter or damage inside the direct fuel injector assembly installation holes (fuel delivery pipe sub-assembly).
    1. Do not allow gasoline to get on the O-rings or inside the installation holes.
    1. If it is difficult to insert the direct fuel injector assembly, apply new engine oil to the chamfer of the direct fuel injector assembly installation hole of the fuel delivery pipe sub-assembly. Be careful not to allow the direct fuel injector assembly to fall out of the fuel delivery pipe sub-assembly.
    1. Do not tilt the direct fuel injector assembly when inserting it into the fuel delivery pipe sub-assembly.
    1. Check that there is no gap between the fuel delivery pipe sub-assembly and the nozzle holder clamp.

    1. A345405E01
      Make sure the 4 direct fuel injector assemblies have the same flow classification number 1, 2 or 3 (the number to the left of the QR code).
      Text in Illustration 
      *a
      QR Code
      *b
      Flow Classification Number



3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
  1. Apply lubricant to the direct fuel injector assembly installation holes of the cylinder head sub-assembly.



    A186827E02
  1. Temporarily install the fuel delivery pipe sub- assembly so that the stud bolts protrude enough to install the nuts.
    Text in Illustration 
    *a
    Protruding enough to install nut

    NOTICE:
    1. If a direct fuel injector assembly is dropped or the tip of a direct fuel injector assembly is struck, replace it with a new one.
    1. Check that there is no foreign matter or damage on the direct fuel injector assembly installation holes of the cylinder head sub-assembly.
    1. When installing the fuel delivery pipe sub-assembly, push it in evenly without tilting it.



    A337371E02
  1. Install the fuel delivery pipe sub-assembly by uniformly tightening the 3 bolts and 2 nuts in the order shown in the illustration.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



4. CONNECT NO. 5 ENGINE WIRE
  1. Connect the fuel pressure sensor connector.

  1. Connect the 4 direct fuel injector assembly connectors.

  1. Connect the No. 5 engine wire to the fuel delivery pipe sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 1 fuel pipe sub-assembly to the fuel delivery pipe sub-assembly and tighten the union nut by hand.

  1. Connect the No. 1 fuel pipe sub-assembly to the fuel pump with seal sub-assembly and tighten the union nut by hand.

    NOTICE:
    Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly when installing.



6. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY


    A337376E01
  1. Using a 17 mm union nut wrench, tighten the union nuts on the fuel pump with seal sub-assembly side of the No. 1 fuel pipe sub-assembly.
    Text in Illustration 
    *a
    17 mm Union Nut Wrench
    *b
    Torque Wrench Fulcrum Length

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    1. When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

  1. Using a 17 mm union nut wrench, tighten the union nuts on the fuel delivery pipe sub-assembly side of the No. 1 fuel pipe sub-assembly.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    1. When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)



7. INSTALL INTAKE MANIFOLD
(Click here)


8. PERFORM INITIALIZATION
  1. Perform "Inspection After Repair" after replacing a direct fuel injector assembly (Click here).