Home › Engine / Hybrid System ยท 6AR-FSE › FUEL › FUEL PUMP

FUEL PUMP > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE REAR SEAT CUSHION ASSEMBLY


    B279202E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



5. REMOVE REAR SEAT CUSHION LOCK HOOK


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



6. REMOVE REAR FLOOR SERVICE HOLE COVER


    A337346E02
  1. Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.
    Text in Illustration 
    *a
    Protective Tape

  1. Disconnect the fuel pump connector.



7. DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A338493E01
  1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel pump tube sub-assembly.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Pump Tube Sub-assembly
    *3
    Fuel Suction Plate Sub-assembly
    *a
    Fuel Tube Joint
    *b
    O-ring
    *c
    Nylon Tube
    V100135
    Pull off
    V100136
    Pull off

    NOTICE:
    1. Remove any foreign matter on the fuel tube joint before performing this work.
    1. Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
    1. Be sure to disconnect the fuel tube joint by hand.
    1. Do not bend, twist, pinch or kink the nylon tube.
    1. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.
    1. If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.



8. REMOVE FUEL TANK VENT TUBE SET PLATE


    A129480
  1. Remove the 8 bolts and fuel tank vent tube set plate.



9. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    A139190
  1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

    NOTICE:
    1. Do not damage the suction filter.
    1. Be careful not to bend the arm of the fuel sender gauge assembly.



    A136023E03
  1. Remove the fuel suction tube set gasket from the fuel suction tube with pump and gauge assembly.
    Text in Illustration 
    *1
    Fuel Suction Tube Set Gasket