ENGINE OIL COOLER > INSTALLATION |
| 1. INSTALL OIL COOLER ASSEMBLY |
Clean the installation surfaces of the oil cooler assembly.
Apply a small amount of engine oil to 3 new gaskets.
Install the 3 gaskets to the oil cooler assembly.
Temporarily install the oil cooler assembly with the oil cooler union bolt, nut and a new seal washer.
![]() |
Using several steps, uniformly install and tighten the oil cooler union bolt and nut in the order shown in the illustration.
| 2. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
| 3. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick.
| 4. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Slowly fill the radiator assembly with engine coolant.
| *a | Code Mark |
| Code Mark "M" | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Code Mark "G" | 7.0 liters (7.4 US qts, 6.2 Imp. qts) |
| Code Mark "Z" | 7.3 liters (7.7 US qts, 6.4 Imp. qts) |
Remove the reserve tank cap.
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the cooling system.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 5. ADD ENGINE OIL |
Add clean engine oil and install the oil filler cap sub-assembly.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL "Energy-Conserving", SM "Energy- Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil |
|
| API grade SL, SM or SN multigrade engine oil |
|
| Item | Specified Condition |
| Drain and refill with oil filter change | 4.4 liters (4.6 US qts, 3.9 Imp. qts) |
| Drain and refill without oil filter change | 4.0 liters (4.2 US qts, 3.5 Imp. qts) |
| Dry fill | 5.3 liters (5.6 US qts, 4.7 Imp. qts) |
| 6. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 7. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.