Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > Clearance Sonar Main Switch Circuit

for Preparation Click here


DESCRIPTION

The back sonar or clearance sonar switch assembly is installed at the base of the driver side of the instrument panel.
When the back sonar or clearance sonar switch assembly is turned on, an on signal is sent to the clearance warning ECU assembly. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM


E222388E34


INSPECTION PROCEDURE

NOTICE:
Inspect the fuse for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Clearance Sonar / Data List.

  1. Read the Data List according to the display on the GTS.

    Clearance Sonar 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Clearance sonar main switch/OFF or ON
    OFF: Back sonar or clearance sonar switch assembly off
    ON: Back sonar or clearance sonar switch assembly on
    -
    Clearance Sonar ECU Type
    Type of clearance sonar ECU/Normal
    Normal: Normal clearance sonar type
    -

    Result:
    Result
    Proceed to
    Both of the following conditions are met:
    1. The display changes as shown above when the back sonar or clearance sonar switch assembly is operated.
    1. "Normal" is displayed.
    A
    "Normal" is not displayed.
    B
    Both of the following conditions are met:
    1. The display does not change as shown above when the back sonar or clearance sonar switch assembly is operated.
    1. "Normal" is displayed.
    C



B
CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)

C
Go to step 2
A

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)  

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
  1. Remove the back sonar or clearance sonar switch assembly (Click here).



    E307481E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (IG) - 3 (ECU)
    Back sonar or clearance sonar switch assembly on
    Below 1 Ω
    6 (IG) - 3 (ECU)
    Back sonar or clearance sonar switch assembly off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Back Sonar or Clearance Sonar Switch Assembly)



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I178-6 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    I178-6 (IG) - Body ground
    Ignition switch off
    Below 1 V



NG
REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
  1. Disconnect the I82 connector from the clearance warning ECU assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I82-9 (CLSW) - I178-3 (ECU)
    Always
    Below 1 Ω
    I82-9 (CLSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)