The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during radio setting condenser removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1. PRECAUTION (w/ Rear Seat Side Airbag)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)
for 2AR-FE:
Click hereGeneral>MAINTENANCE>2AR-FE BATTERY>REMOVAL
for A25A-FKS:
Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for 2GR-FKS:
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an airbag deploys for any reason, it may cause a serious injury.
73350C
3.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)
4.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
72693
5.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
62332A
6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)
7.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
71940A
8.REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)
73350C
9.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Reclining Seat Type)
10.REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)
72693
11.REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)
72996A
12.REMOVE REAR SEATBACK COVER (for Reclining Seat Type)
13.REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)
62332A
14.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type)
15.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Reclining Seat Type)
62472A
16.REMOVE INNER ROOF SIDE GARNISH LH
86011V
17.REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)
When a terminal cover is removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.
Remove the bolt.
Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
|
Remove in this Direction |
Disengage the claw and pull out the cover as shown in the illustration.
|
Remove in this Direction |
Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser as shown in the illustration.
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Use the same procedure for the other terminal cover.
Remove the 2 terminal covers from the wire harness.
Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
Check for deformation of the terminal after the wire harness has been removed from the terminal cover.
86011R
18.REMOVE RADIO SETTING CONDENSER (for Window Defogger)
When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.
Remove the bolt.
Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.
|
Remove in this Direction |
Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser as shown in the illustration.
Using a screwdriver, bend back and break off the claw as shown in the illustration.
Remove the terminal cover from the wire harness.
Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.
Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.
Check for deformation of the terminal after the wire harness has been removed from the terminal cover.