1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.REMOVE HEADLIGHT ASSEMBLY LH
for LED Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>REMOVAL
for Bulb Type Turn Signal Light:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
3.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52611
4.REMOVE FRONT BUMPER ENERGY ABSORBER
52131A
5.REMOVE FRONT BUMPER REINFORCEMENT
53253B
6.REMOVE UPPER RADIATOR MOUNTING BRACKET
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE (COOLING)>RADIATOR>REMOVAL
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (COOLING)>RADIATOR>REMOVAL
for 2GR-FKS:
Click hereEngine / Hybrid System>2GR-FKS (COOLING)>RADIATOR>REMOVAL
17750A
7.REMOVE INLET AIR CLEANER ASSEMBLY
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS:
Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
53510
8.REMOVE HOOD LOCK ASSEMBLY
16691A
9.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH
16595B
10.REMOVE NO. 1 RADIATOR AIR GUIDE LH
|
Remove in this Direction |
Remove the clip.
Disengage the claw and guide, and remove the No. 1 radiator air guide LH as shown in the illustration.
16593B
11.REMOVE NO. 1 RADIATOR AIR GUIDE RH
|
Remove in this Direction |
Disconnect the connector.
Remove the clip.
Disengage the claw and guide, and remove the No. 1 radiator air guide RH as shown in the illustration.
88711
12.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose sub-assembly from the cooler condenser assembly.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88710E
13.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
While pressing the end of the air conditioning tube and accessory assembly into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.
| *1 | Air Conditioning Tube and Accessory Assembly | *2 | Cooler Condenser Assembly |
| *3 | Piping Clamp | - | - |
| *a | Press In | - | - |
If any foreign matter is adhered to the connecting part, brush it off or use compressed air to remove it.
Make sure that fragments of the piping clamp do not enter the piping.
Disconnect the air conditioning tube and accessory assembly.
Clean off any foreign matter on and near the ends of the air conditioning tube and accessory assembly and cooler condenser assembly.
Remove the 2 O-rings from the air conditioning tube and accessory assembly.
Wrap the open ends of the separated cooler condenser assembly and air conditioning tube and accessory assembly with vinyl tape to prevent entry of moisture and foreign matter.
Remove the piping clamp.
53205
14.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE (COOLING)>RADIATOR>REMOVAL
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (COOLING)>RADIATOR>REMOVAL
for 2GR-FKS:
Click hereEngine / Hybrid System>2GR-FKS (COOLING)>RADIATOR>REMOVAL
88460
15.REMOVE COOLER CONDENSER ASSEMBLY
|
Remove in this Direction |
Disengage the 2 claws and 2 guides, and remove the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.