Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2017.09–2017.12
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321407 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.SECURE STEERING WHEEL

Hide 7.REMOVE FRONT WHEELS

Hide 53851M 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.

Remove the 3 screws and front wheel opening extension pad RH.


Hide 53852K 9.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.

Remove the 3 screws and front wheel opening extension pad LH.


Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.


Hide 53737B 11.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 2 screws, clip and front fender apron seal LH.


Hide 53736 12.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 2 screws, clip and front fender apron seal RH.


Hide 52119A 13.REMOVE FRONT BUMPER COVER

Hide 52618 14.REMOVE FRONT LOWER BUMPER ABSORBER

a.
A407916

Remove the 4 bolts.


b.

Disengage the 2 claws to remove the front lower bumper absorber.


Hide 15.DRAIN ENGINE COOLANT

Hide 12601B 17.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A407917

Lift the rear of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the front of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17750A 18.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A407918

Remove the 2 bolts and inlet air cleaner assembly.


Hide 19.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A407919

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 3 wire harness clamps.


c.
A407920

Slide the clip and disconnect the ventilation hose from the cylinder head cover sub-assembly.


d.

Disengage the 2 clamps.


e.

Loosen the hose clamp and disconnect the air cleaner assembly with air cleaner hose from the throttle body with motor assembly.

A407921C01
1.5,1.26 2.167,1.229 2.167,1.229 1.917,0.667 true 2.188,1.219 2.229,0.875 true 2.198,1.26 2.51,1.458 0.313,0.198 10 false *a
*a Pin - -


NOTICE:

Make sure the air cleaner support remains attached to the vehicle body.



f.

Disengage the 3 pins to remove the air cleaner assembly with air cleaner hose.


Hide 21.DISCONNECT WIRE HARNESS

a.
A407936

Remove the nut and disconnect the wire harness from the positive (+) battery terminal.


Hide 22.REMOVE BATTERY

Hide 74404A 23.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A407922

Disengage the 5 clamps from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly.


Hide 33820B 24.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C378121

Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever.


b.
C378137

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 23901 25.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23826 26.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A407927

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.


Hide 44774 27.DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.
A407929

Slide the clip and disconnect the union to connector tube hose.


Hide 44773F 28.DISCONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.
A407928

Slide the clip and disconnect the union to check valve hose.


Hide 16571C 29.DISCONNECT NO. 1 RADIATOR HOSE

a.
A407931

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 30.DISCONNECT NO. 2 RADIATOR HOSE

a.
A407930

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 88711 31.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 32.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 33.DISCONNECT WATER HOSE

a.
A407932

Slide the 4 clips and disconnect the 4 water hoses.


b.

Disengage the 4 clamps.


Hide 34.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A407938

Remove the 2 bolts.


b.
A407926

Remove the relay block cover.


c.
A408433

Remove the nut.


d.

Disconnect the 4 connectors.


e.

Using a screwdriver, disengage the claw and separate the wire harness from the engine room relay block and junction block assembly.


f.
A407939

Remove the bolt and disconnect the wire harness from the vehicle body.


Hide 45220 35.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 36.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 11361J 38.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A407945

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 32101A 39.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 40.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not position the height adjustment attachments or plate lift attachments under the front cross member sub-assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.




b.
A407943

Disengage the clamp.


c.
A407940

Remove the 2 bolts, nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
A407941

Remove the bolt, nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


e.
A407942C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 8 bolts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


f.

Remove the 4 bolts, 2 nuts, front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 41.INSTALL ENGINE HANGERS

a.
A407947C01
0.531,2.052 0.729,2.052 0.729,2.052 0.906,1.583 true 2.969,2.063 2.802,2.063 2.802,2.063 2.667,1.427 true 0.354,1.969 0.667,2.167 0.313,0.198 10 false *1 3.031,1.979 3.344,2.177 0.313,0.198 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-36020
No. 2 Engine Hanger 12282-36021
Bolt 91552-81040 or
91552-81025



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 28100 42.REMOVE STARTER ASSEMBLY

Hide 51100G 44.REMOVE FRONT FRAME ASSEMBLY

a.
A407948

Remove the 7 nuts and front frame assembly.


Hide 12361A 45.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A407949

Remove the bolt and front engine mounting insulator from the front engine mounting bracket.


Hide 12371A 46.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A407950

Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.


Hide 32942 47.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 32941 48.DISCONNECT INLET NO. 1 OIL COOLER HOSE

Hide 33493A 49.REMOVE TRANSMISSION OIL COOLER

Hide 32101 53.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 82121 54.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 55.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 56.REMOVE ENGINE HANGERS

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 12305 57.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A413646

Disconnect the No. 6 water by-pass hose.


b.

Disengage the clamp.


c.

Remove the bolt, nut and the radiator reserve tank assembly.


d.
A407952

Remove the bolt and disconnect the bracket from the engine mounting insulator sub-assembly RH.


e.
A420751

Remove the bolt and disconnect the No. 1 bond cable from the engine mounting insulator sub-assembly RH.


f.
A407953

Disengage the clamp.


g.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.


Hide 12341 58.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A407954

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12304 59.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A412656

Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.


Hide 12372A 60.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL