Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › 2017.09–2017.12
RM33A0E _54 Brake _065366 BRAKE SYSTEM (OTHER) _0319142 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines or refrigerant lines.



b.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



c.

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 47264A 3.INSTALL PUSH ROD PIN

Hide 4.INSTALL BRAKE LINE

a.

Engage the 3 clamps to install a new No. 2 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.



b.
C380318

Engage the clamp and install the No. 2 brake tube clamp to the vehicle body.

NOTICE:

Do not kink or damage the brake lines.



c.
C380319

Install the front brake tube way to the vehicle body with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 44773F 5.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the brake booster assembly and slide the clip to secure it.


Hide 88710E 6.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.
C380313

Insert the air conditioner tube and accessory assembly to the air conditioning unit assembly.


e.
C380317

Engage the clamp to install the air conditioner tube and accessory assembly.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




f.
C380316

Connect the connector to the air conditioner tube and accessory assembly.


Hide 88707 7.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Insert the suction pipe sub-assembly to the air conditioning unit assembly.


e.
C380312

Rotate the hook connector as shown in the illustration.


f.

Insert the tube joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


g.
C380315

Engage the clamp to install the suction pipe sub-assembly to the engine mounting insulator sub-assembly RH.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




h.
C380314

Engage the clamp to install the suction pipe sub-assembly to the brake tube clamp bracket.

NOTICE:
·

Do not deform the refrigerant lines.

·

Do not damage the clamp.




Hide 55606 8.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111A 9.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67913 10.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 11.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 12.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 15.INSPECT AND ADJUST BRAKE PEDAL