Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL INJECTOR (for Port Injection)
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319414 FUEL INJECTOR(for Port Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of spindle oil or gasoline to 6 new O-rings, and install one to each fuel injector assembly.

NOTICE:

Check that there is no damage or foreign matter on the groove of the fuel injector assembly when installing the O-ring to each fuel injector assembly.



b.

for Bank 1:

i.

Connect the 3 fuel injector assembly connectors.


ii.
A368859C01
0.771,1.948 1.354,1.948 true 2.021,1.188 2.323,1.188 false 1.396,1.865 1.708,2.021 0.313,0.156 10 false *a 2.365,1.104 2.677,1.26 0.313,0.156 10 false *a
*a Stopper


Install the 3 fuel injector assemblies to the fuel delivery pipe with sensor assembly.

NOTICE:
·

Make sure that the fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the fuel injector assembly installation holes of the fuel delivery pipe with sensor assembly are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the fuel injector assembly.




iii.

Engage the clamp to connect the No. 5 engine wire to the fuel delivery pipe with sensor assembly.



c.

for Bank 2:

i.

Connect the 3 fuel injector assembly connectors.


ii.
A368860C01
1.375,1 1.625,1 false 2.063,2 2.729,2 true 1.896,1.906 2.208,2.063 0.313,0.156 10 false *a 1.208,0.906 1.521,1.063 0.313,0.156 10 false *a
*a Stopper


Install the 3 fuel injector assemblies to the fuel delivery pipe with sensor assembly.

NOTICE:
·

Make sure that the fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the fuel injector assembly installation holes of the fuel delivery pipe with sensor assembly are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the fuel injector assembly.




iii.

Engage the clamp to connect the No. 5 engine wire to the fuel delivery pipe with sensor assembly.



Hide 23291 2.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 6 new injector vibration insulators to the intake manifold.


Hide 23807V 3.INSTALL NO. 1 DELIVERY PIPE SPACER

a.

Install the 4 No. 1 delivery pipe spacers to the intake manifold.


Hide 23800 4.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.

Place the fuel delivery pipe with sensor assembly with the 6 fuel injector assemblies onto the intake manifold.

NOTICE:

Be careful not to drop the fuel injector assemblies when installing the fuel delivery pipe with sensor assembly.



b.

Install the fuel delivery pipe with sensor assembly with the fuel injector assemblies with the 4 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


c.

Connect the 2 No. 5 engine wire connectors.


d.

Connect the fuel pressure sensor connector.


Hide 5.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 17190 6.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 9.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION