Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2017.09–2017.12
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0319581 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48691C 1.INSTALL SUSPENSION TOWER DAMPER (w/ Suspension Tower Damper)

a.

Install the suspension tower damper to the front shock absorber assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 48158C 2.INSTALL FRONT LOWER COIL SPRING INSULATOR

a.
C370097C01
0,0 0,0 false
V100135

Positioning Pin


Install the front lower coil spring insulator to the front shock absorber assembly.

NOTICE:

When installing the front lower coil spring insulator, insert the positioning pin of the spring seat into the hole of the front lower coil spring insulator.



Hide 48331C 3.INSTALL FRONT SPRING BUMPER

a.
C370098

Install the front spring bumper to the front shock absorber assembly.

NOTICE:
·

Face the smaller diameter end of the front spring bumper downward.

·

Do not apply lubricants to the front spring bumper.

·

Do not apply lubricants to the front shock absorber assembly cap or rod.

·

Do not clean the front spring bumper with water or solvent.




Hide 48132 4.INSTALL FRONT COIL SPRING

a.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00051  
09727-30022  (09727-00010, 09727-00031)


b.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989

Make sure that the hooks are securely attached to the coil spring.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370089

Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C312080

Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




c.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990

·

Make sure that the stopper pins are installed securely.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




d.

Using SST, compress the coil spring.

CAUTION:
·
C370091

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370092

Do not compress the coil spring to the point where the coils touch each other.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C370093

Do not use an impact wrench.

·

If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

·
C344912N01
0.885,3.167 1.708,3.167 true 0.583,3.083 0.896,3.24 0.313,0.156 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


e.
C388458C01
0.438,0.292 0.615,0.292 0.615,0.292 0.615,1.323 true 0.281,0.208 0.594,0.365 0.313,0.156 10 false *a
*a Depression


Align the end of the front coil spring with the flange of the front lower coil spring insulator and install the front coil spring.

NOTICE:

Make sure to fit the end of the front coil spring that has the larger diameter into the depression of the front lower coil spring insulator.



Hide 48619A 5.INSTALL STRUT MOUNTING BEARING

a.
C370017C01
2.438,0.698 3,0.698 false 2.406,0.792 2.875,1.24 2.875,1.24 2.979,1.24 false 3.042,0.625 3.354,0.781 0.313,0.156 10 false *1 3.021,1.167 3.333,1.323 0.313,0.156 10 false *a
*1 Strut Mounting Bearing
*a Top End of the Front No. 1 Shock Absorber Dust Cover


Install the strut mounting bearing to the front No. 1 shock absorber dust cover.

NOTICE:

Make sure that the top end of the front No. 1 shock absorber dust cover and strut mounting bearing are securely attached.



Hide 48157C 6.INSTALL FRONT UPPER COIL SPRING INSULATOR

a.

Install the front upper coil spring insulator to the strut mounting bearing.


Hide 7.INSTALL STRUT MOUNTING BEARING WITH DUST COVER

a.

Install the strut mounting bearing with dust cover to the front shock absorber assembly.


Hide 48609 8.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.
C388459C01
2.146,0.875 2.813,0.333 2.813,0.333 2.917,0.333 true 2.958,0.26 3.271,0.417 0.313,0.156 10 false *a
*a Slot
V100135

Outside of the Vehicle


Install the front suspension support sub-assembly as shown in the illustration.

NOTICE:

Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.



b.
C370101C01
0.688,0.708 0.792,0.708 0.792,0.708 1.656,1.26 true 1.854,1.042 2.615,1.042 true 1.708,1.948 2.563,1.948 true 0.604,1.25 0.677,1.25 0.677,1.25 1.667,2.063 true 0.677,3.042 0.771,3.042 0.771,3.042 1.667,3.469 true 1.719,3.125 2.656,3.125 true 2.042,0.177 2.396,0.469 0.354,0.292 10 false *a 1.74,2.344 2.052,2.604 0.313,0.26 10 false *b 0.531,0.635 0.833,0.906 0.302,0.271 10 false *c 2.594,1.875 2.906,2.156 0.313,0.281 10 false *d 0.448,1.177 0.792,1.417 0.344,0.24 10 false *e 2.646,0.969 2.958,1.125 0.313,0.156 10 false *f 0.521,2.948 0.854,3.271 0.333,0.323 10 false *g 1.51,2.344 1.844,2.563 0.333,0.219 10 false *b 2.688,3.042 3.031,3.281 0.344,0.24 10 false *e
*a 0° +/- 3°
*b 15°
*c Alignment Mark of Front Suspension Support Sub-assembly
*d Guide Line of Front Suspension Support Sub-assembly
*e Alignment Mark of Strut Mounting Bearing
*f Front Shock Absorber Lower Bracket
*g Arrow of Shock Absorber Dust Cover
V100135

Outside of the Vehicle


Align the alignment mark of the front suspension support sub-assembly with the front shock absorber lower bracket as shown in the illustration.

NOTICE:

Make sure to install the front suspension support sub-assembly so that the alignment mark of the front suspension support sub-assembly is aligned within +/- 3° of the center of the front shock absorber lower bracket.



c.

Align the alignment mark of the strut mounting bearing with the guide line of the front suspension support sub-assembly as shown in the illustration.

NOTICE:

Make sure to install the strut mounting bearing so that the alignment mark of the strut mounting bearing is aligned within +/- 15° of the guide line of the front suspension support sub-assembly.



d.

Align the arrow of the shock absorber dust cover with the alignment mark of the strut mounting bearing as shown in the illustration.


Hide 48609E 9.TEMPORARILY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Temporarily tighten a new front support to front shock absorber nut.


b.

Remove SST from the front coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48559B 10.CONNECT FRONT NO. 1 SHOCK ABSORBER DUST COVER

a.
C370016C01
1.813,1.406 1.594,1.906 1.594,1.906 1.25,1.417 true 0.479,1.115 0.563,1.115 0.563,1.115 1.156,1.385 false 0.333,1.042 0.646,1.198 0.313,0.156 10 false *1 1.542,1.938 1.854,2.094 0.313,0.156 10 false *a
*1 Front No. 1 Shock Absorber Dust Cover
*a Claw


Connect the end of the front No. 1 shock absorber dust cover with the claws of the front shock absorber assembly.

NOTICE:
·

Make sure that the end of the front No. 1 shock absorber dust cover is securely attached to the claws of the front shock absorber assembly.

·

Make sure there is no excessive damage to the bellows of the front No. 1 shock absorber dust cover.

·

Do not allow oil, grease, etc., to contact the front No. 1 shock absorber dust cover.

·

If there is oil or grease on the insulator, wipe clean with a cloth. Do not use an alcohol based cleaner.




Hide 11.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Install the front shock absorber with coil spring (upper side) with the 3 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:
·

When installing the nuts, keep the bolts from rotating.

·

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.



HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 48609E 12.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Fully tighten the front support to front shock absorber nut.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)

NOTICE:

Perform this step only when the front shock absorber with coil spring has been disassembled.



Hide 89543 13.INSTALL FRONT SPEED SENSOR

a.
C370102C01
0,0 0,0 false
V100135

Hook


Engage the 2 hooks to install the front speed sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C370084

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



c.

Engage the clamp.

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 48810 14.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 55708 15.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 16.INSTALL FRONT WHEEL

Hide 17.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 18.PERFORM INITIALIZATION

Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Lighting system (EXT) (Click here)