Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT › 2017.09–2021.02
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0319583 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C370106

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C370107

Remove the cotter pin.


c.

Remove the nut.


d.
C370108C01
0.896,0.094 1.292,0.094 1.292,0.094 1.292,1.063 true 1.156,0.094 1.156,1.063 true 3.042,0.927 3.354,1.083 0.313,0.156 10 false *a 0.594,0.021 1.052,0.219 0.458,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C370109C01
1.469,1.344 1.885,1.344 false 0.896,4.354 0.99,4.354 0.99,4.354 1.198,3.99 false 2.406,2.698 2.802,2.031 2.802,2.031 2.896,2.031 true 1.615,1.771 2.219,1.771 false 0.74,4.271 1.052,4.427 0.313,0.156 10 false *a 2.313,0.76 2.625,0.917 0.313,0.156 10 false *b 1.313,1.26 1.625,1.417 0.313,0.156 10 false *c 2.938,1.948 3.25,2.104 0.313,0.156 10 false *d 2.313,0.385 2.625,0.542 0.313,0.156 10 false *b 2.083,3.729 2.396,3.885 0.313,0.156 10 false B 2.083,3.448 2.396,3.604 0.313,0.156 10 false A 2.26,1.688 2.719,1.885 0.458,0.198 10 false SST
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the front axle assembly to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.