Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › 2017.09–2017.12
RM33A0E _52 Drivetrain _065359 AXLE AND DIFFERENTIAL _0319633 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Suspension, tires
(The vehicle height changes because of suspension or tire replacement.)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Rear height control sensor sub-assembly LH Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 58399D 2.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 58398F 3.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 890C0A 4.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C371415

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




b.
C376651C03
1.573,1.771 1.865,1.771 1.865,1.771 1.865,1.469 true 1.333,1.688 1.563,1.865 0.229,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly or connector cover.



c.
C376653

Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE

a.
C379274

Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.


Hide 6.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42431 7.REMOVE REAR DISC

Hide 42450B 8.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 9.REMOVE REAR FLEXIBLE HOSE BRACKET

a.
C376654

Remove the bolt and rear flexible hose bracket from the rear axle carrier sub-assembly.


Hide 89408C 10.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 48840A 11.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 12.REMOVE REAR COIL SPRING

Hide 48258C 13.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48720A 14.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 42305 15.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C370183

Loosen the 2 bolts of the rear trailing arm assembly.


b.
C370184C02
0.958,0.688 1.208,0.688 1.208,0.688 1.385,1.01 true 0.698,0.594 0.969,0.823 0.271,0.229 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C370185C01
1.469,2.375 1.958,2.375 false 1.448,3.031 1.938,3.031 false 1.292,2.26 1.604,2.417 0.313,0.156 10 false *a 1.302,2.938 1.615,3.094 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear axle carrier sub-assembly.

NOTICE:
·

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C370186N01
1.104,0.417 1.26,0.615 0.156,0.198 10 true A

Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


f.

Remove the nut and plate washer, and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



g.

Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.