Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › 2017.09–2017.12
RM33A0E _53 Suspension _065362 REAR SUSPENSION _0319636 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48259A 1.INSTALL REAR UPPER COIL SPRING INSULATOR

a.

Install the rear upper coil spring insulator to the vehicle.


Hide 48258C 2.INSTALL REAR LOWER COIL SPRING INSULATOR

a.

Install the rear lower coil spring insulator to the rear No. 2 suspension arm assembly.


Hide 48231B 3.INSTALL REAR COIL SPRING

a.
C345081C03
1.833,3.854 2.26,3.854 true 1.865,3.927 2.063,3.927 2.063,3.927 2.063,3.854 true 1.583,1.406 1.417,1.406 1.417,1.406 1.417,1.906 true 2.271,3.76 2.583,3.917 0.313,0.156 10 false *a 0.583,0.927 0.896,1.083 0.313,0.156 10 false *b 0.583,1.49 0.896,1.646 0.313,0.156 10 false *b 1.323,1.938 1.635,2.094 0.313,0.156 10 false *c
*a Identification Mark
*b 30° or less
*c Lower End of Rear Coil Spring
V100135

Inner Side of the Vehicle


Set the rear coil spring to the rear No. 2 suspension arm assembly.

NOTICE:
·

Set the rear coil spring so that its lower end is within the range shown in the illustration.

·

Set the rear coil spring so that the identification mark is positioned as shown in the illustration.

·

The smaller diameter end must face upward.




b.

Using a jack and wooden block, slowly jack up the rear No. 2 suspension arm assembly and then install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and nut.

CAUTION:

Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.


NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.

·

Insert the bolt with the threaded end facing the front of the vehicle.




Hide 48740F 5.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.
C376668

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48840A 6.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 58398F 7.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58399D 8.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 89408C 9.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)

Hide 10.INSTALL REAR WHEEL

Hide 48740F 11.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 12.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 13.PERFORM INITIALIZATION

Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Lighting system (EXT) (Click here)